Gel Doc™ XR ChemiDoc™ XRS

More documents

Recommendations

Info

General Precautions • Please read the instruction manual carefully. • The instrument must be used only for the intended purpose of gel documentation in research laboratories. • The instrument must be connected to a power source line which MUST BE grounded and protected by a circuit breaker. • Do not pour liquids directly on or inside the instrument. • Switch off all the lights immediately after use. • Clean the transilluminator platen after use. Generelle Vorsichtsmassnahmen • Bitte die Bedienungsanleitung aufmerksam lesen. • Das Geraet darf nur fuer die vorgesehenen Applikationen eingesetzt werden, d.h. Geldokumentation in Forschungslaboratorien. • Fuer die Stromversorgung des Hood muss eine geerdtete Steckdose benutzt werden. • Keine Fluessigkeiten auf oder in das Geraet giessen. • Die Lampe sofort nach dem Gebrauch ausschalten. • Den UV-Filter des transilluminators nach Gebrauch reinigen. Page 4 of 42
TABLE OF CONTENTS HARDWARE INSTRUCTION MANUAL ..................................................................................................................1 SECTION 1 INTRODUCTION.....................................................................................................................................7 1.1 COMPUTER REQUIREMENTS ......................................................................................................................................7 1.2 PC ...........................................................................................................................................................................7 1.3 MACINTOSH ..............................................................................................................................................................7 SECTION 2 IMPORTANT SAFETY INFORMATION.............................................................................................8 2.1 IMPORTANT NOTICE ..................................................................................................................................................8 2.2 POWER SAFETY INFORMATION ...................................................................................................................................8 SECTION 3 PRODUCT DESCRIPTION ....................................................................................................................9 3.1 CCD CAMERA AND LENSES .......................................................................................................................................9 3.2 DARKROOM ENCLOSURE, EMISSION FILTERS, AND ILLUMINATION SOURCES ...............................................................9 3.3 PCI INTERFACE CARDS ..........................................................................................................................................10 3.4 QUANTITY ONE® SOFTWARE...................................................................................................................................10 3.5 PRINTER (OPTIONAL) ..............................................................................................................................................10 3.6 PACKAGING ............................................................................................................................................................10 SECTION 4 GETTING STARTED ............................................................................................................................12 4.1 SELECTING A LOCATION ..........................................................................................................................................12 4.2 ASSEMBLING THE SYSTEM........................................................................................................................................12 4.2.1 Assembling the Universal Hood II .................................................................................................................12 4.2.2 Assembling the CCD Camera ........................................................................................................................13 4.2.3 Connecting the cabling harnesses..................................................................................................................15 4.2.4 Installing the White Light Transilluminator (Optional)...............................................................................16 4.2.5 Installing the Optional 17 mm or 25 mm Wide-Angle Lenses (ChemiDoc XRS only):..............................16 4.3 Description of System Function and System Initialization................................................................................18 4.3.1 Control panel .................................................................................................................................................18 4.3.2 System Initialization.......................................................................................................................................21 4.3.3 Aligning the Camera assembly: .....................................................................................................................24 SECTION 5 OPERATION OF THE UNIVERSAL HOOD II.................................................................................25 5.1 OPERATING THE UNIT..............................................................................................................................................25 5.1.1 Switch on the Universal Hood II....................................................................................................................25 5.1.2 Position your gel ............................................................................................................................................25 5.1.3 Acquire an image ...........................................................................................................................................25 5.1.4 Acquiring an image with Flat Fielding:.........................................................................................................25 5.2 CUTTING GELS ........................................................................................................................................................28 SECTION 6 TROUBLE SHOOTING.........................................................................................................................29 SECTION 7 ACCESSORIES AND REPLACEMENT PARTS...............................................................................30 Accessories and Replacement Parts........................................................................................................................30 SECTION 8 MAINTENANCE AND PART REPLACEMENT...............................................................................32 8.1 EPI-ILLUMINATION LAMP REPLACEMENT ..................................................................................................................32 8.2 FUSE REPLACEMENT................................................................................................................................................32 8.3 UV TRANSILLUMINATOR..........................................................................................................................................33 8.3.1Lamp replacement...........................................................................................................................................33 8.3.2 Starter replacement (P/N 100-1370)..............................................................................................................34 APPENDIX A: GEL DOC XR SYSTEM CABLE CONFIGURATION..............................................................35 APPENDIX B: CHEMIDOC XRS SYSTEM CABLE CONFIGURATION .......................................................36 APPENDIX C: INSTALLING SOFTWARE AND DRIVERS ................................................................................37 Gel Doc XR and ChemiDoc XRS- PC: .............................................................................................................37 Gel Doc XR and ChemiDoc XRS- Mac: ...........................................................................................................39 Page 5 of 42
Page 1 and 2: Gel Doc XR ChemiDoc XRS 170-8170
Page 3: Regulatory Notice IMPORTANT: The Ge
Page 7 and 8: Section 1 Introduction The Bio-Rad
Page 9 and 10: Section 3 Product Description 3.1 C
Page 11 and 12: Part # Descriptions 170-8170/170-81
Page 13 and 14: 4.2.2 Assembling the CCD Camera Gel
Page 15 and 16: Center the lens in the opening of t
Page 17 and 18: Setting Up the Lens: 1. Turn off th
Page 19 and 20: The Imaging led blinks when you are
Page 21 and 22: Filters: A +1 Diopter is factory in
Page 23 and 24: 1. Make sure that all lights in the
Page 25 and 26: Section 5 Operation of the Universa
Page 27 and 28: 10. Remove the sample from the tran
Page 29 and 30: Section 6 Trouble Shooting Problem
Page 31 and 32: 100-2784 UV transilluminator Lid (I
Page 33 and 34: This unit is protected by 2 fuses 5
Page 35 and 36: Appendix A: Gel Doc XR System Cable
Page 37 and 38: Appendix C: Installing Software and
Page 39 and 40: Gel Doc XR and ChemiDoc XRS- Mac: a
Page 41 and 42: Appendix D: PCI Card Installation P

Gel Doc™ XR ChemiDoc™ XRS

Create successful ePaper yourself

Delete template?

Save as template?