Gel Doc™ XR ChemiDoc™ XRS

More documents

Recommendations

Info

Upon completion of the Camera installation, refer to Section 4.2.3 and Appendix A for a complete description of the cable connections. ChemiDoc XRS a) Place the Camera on the bench so that the locking hole of the tripod mount is facing you. b) Fix the ChemiDoc XRS bracket to the Camera, do not tighten the screw. c) Place the black adapter ring (6 millimeters thickness) on the top of the hood with its soft side facing up. Tripod Mount ChemiDoc XRS Camera with bracket Black adapter ring for ChemiDoc XRS Camera and its positioning on the top of the Hood d) Position the ChemiDoc XRS Camera over the opening on the top of the enclosure by inserting the lens through the adapter ring. Make sure that the lens is in close contact with the black adapter ring. Adjust the Camera position such the lens is well centered in the opening of the hood (see below). Page 14 of 42
Center the lens in the opening of the hood as viewed from inside of the hood e) Fix the Camera bracket to the bracket on the Universal Hood II using the screw, washer and knurled knob. f) Lower the Camera so that the lens fit properly on the gasket of the black adapter ring then tighten the black screw on the tripod mount Upon completion of the Camera installation, refer to Section 4.2.3 and Appendix B for a complete description of the cable connections. 4.2.3 Connecting the cabling harnesses The cable connections are different if you are installing a Gel Doc XR or a ChemiDoc XRS Camera. Please refer to the instructions included in Appendix A, B respectively for Gel Doc XR/ ChemiDoc XRS cable wiring. The controls for the Motorized Zoom Lens can be operated from the membrane touch pad of the Universal Hood II or from the PC using the buttons that appear in the window when the option Gel Doc XR or ChemiDoc XRS is selected in the File Menu of the Quantity One® program. To use this option it is necessary to connect the Universal Hood II serial port (DB25) (on the back left side) to the COM1 of the computer. The PC/Mac cable is included. Note: In the case when a Mac has a USB port instead of the serial port, use the USB to serial adapter (included with Mac systems) to control the lens via software. Page 15 of 42
Page 1 and 2: Gel Doc XR ChemiDoc XRS 170-8170
Page 3 and 4: Regulatory Notice IMPORTANT: The Ge
Page 5 and 6: TABLE OF CONTENTS HARDWARE INSTRUCT
Page 7 and 8: Section 1 Introduction The Bio-Rad
Page 9 and 10: Section 3 Product Description 3.1 C
Page 11 and 12: Part # Descriptions 170-8170/170-81
Page 13: 4.2.2 Assembling the CCD Camera Gel
Page 17 and 18: Setting Up the Lens: 1. Turn off th
Page 19 and 20: The Imaging led blinks when you are
Page 21 and 22: Filters: A +1 Diopter is factory in
Page 23 and 24: 1. Make sure that all lights in the
Page 25 and 26: Section 5 Operation of the Universa
Page 27 and 28: 10. Remove the sample from the tran
Page 29 and 30: Section 6 Trouble Shooting Problem
Page 31 and 32: 100-2784 UV transilluminator Lid (I
Page 33 and 34: This unit is protected by 2 fuses 5
Page 35 and 36: Appendix A: Gel Doc XR System Cable
Page 37 and 38: Appendix C: Installing Software and
Page 39 and 40: Gel Doc XR and ChemiDoc XRS- Mac: a
Page 41 and 42: Appendix D: PCI Card Installation P

Gel Doc™ XR ChemiDoc™ XRS

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?