Bluestar Silicones Rhodorsil® Bases & Gums Product Line

Product
As
Molded
Duro
(ShA)
After
Post
Cure
Rhodosil ® Bases cont’d
Bluestar Silicones Rhodorsil ® Bases & Gums Product Line
SpG
Tear Strength
(ppi)
As
Molded
After
Post
Cure
Tensile
Strength (psi)
As
Molded
After
Post
Cure
Elongation
@ Break, (%)
As
Molded
After
Post
Cure
900 Series (General Purpose - High Resiliency) w/ Catalyst E (1.1%~1.25% pbw)
Resiliency
(%)
As
Molded
After
Post
Cure
Compression
Set (%)
As
Molded
MF 940 U 41 46 1.11 75 80 1190 1130 655 515 52 61 51 27
MF 950 U 52 50 1.11 80 75 1410 1075 480 365 52 34 65 56
MF 960 U 58 61 1.16 70 65 1000 1030 260 250 55 57 38 25
MF 970 USP 68 70 1.17 115 105 1235 1205 380 350 51 54 60 42
MF 980 U 75 78 1.18 100 90 1290 1160 280 230 61 60 63 34
THT Series (Very High Temperature Use) w/ Catalyst E (1.1%~1.25% pbw)
MM 40 THT 39 39 1.09 80 70 870 890 555 470 43 31 57 52
MM 50 THT 42 49 1.13 105 90 1015 1075 550 485 63 43 52 54
MM 60 THT 50 56 1.16 115 110 1265 1365 510 460 66 42 47 50
MM 70 THT 58 64 1.19 120 115 1305 1380 510 410 74 54 38 43
Rhodorsil ® Gums
Product Vinyl Type
Vinyl Content
(ppm) / [mol%]
Consistency
Penetration Value 1/10mm
Volatile Content
(15 min. @ 315° 10 mmHg)
After
Post
Cure
Properties Additives
�Translucent
�Excellent balance
between Compression
set, Tensile strength,
Elongation@break
�Outstanding resiliency
�Good thermal stability
�No tackiness
�Good mechanical
properties balance
�Excellent heat stability
up to 300°C
Appearance
FB None 0 700-1000 3 max. Translucent
751 End & Chain (800) / [0.25] 600-900 3 max. Translucent
753 End & Chain (500) / [0.15] 600-900 3 max. Translucent
759 End (100) / [0.03] 600-900 3 max. Translucent
795 Chain (700) / [0.20] 600-900 3 max. Translucent
DA22
- Demolding Aid
AD 904
- Improve Green Strength
AD 916
- Reduce Compression
Set
Processing Aids
RP 110 ST
- Standard Applications
RP 120 PA
- Platinum Cure Systems
RP 130 Vi
- Vinylated & Hydroxyl
Oil
RP 140 PH
- Phenylated Oil
RG 150 HTS
- High Vinyl Content
Gum
- The typical properties listed above are not intended for use in preparing specifications. The purchaser has the sole responsibility to select a particular Bluestar Silicones Rhodorsil ® product and determine its application suitability.
- Postcure 4 hours at 200◦C - Catalyst E = 2.4 Dichlorobenzoyl peroxide (dilution is @ 50% in weight)
Two Tower Center Blvd., Suite 1601 ▪ East Brunswick ▪ NJ ▪ 08816 ▪ 1-866-474-6342

Product
As
Molded
Duro
(ShA)
2006
Edition
After
Post
Cure
SpG
Tear Strength
(ppi)
As
Molded
After
Post
Cure
Tensile
Strength (psi)
As
Molded
After
Post
Cure
Elongation
@ Break, (%)
As
Molded
Resiliency
(%)
Compression
Set (%)
Properties Additives
- The typical properties listed above are not intended for use in preparing specifications. The purchaser has the sole responsibility to select a particular Bluestar Silicones Rhodorsil ® product and determine its application suitability.
- Postcure 4 hours at 200 ◦ C
- Catalyst E = 2.4 Dichlorobenzoyl peroxide (dilution is @ 50% in weight)
After
Post
Cure
As
Molded
100 Series (General Purpose - High Transparency) w/ Catalyst E (1.1%~1.25% pbw)
After
Post
Cure
As
Molded
MF 135 U 36 41 1.10 100 100 1060 1190 480 420 52 530 - 39
MF 160 USP 56 62 1.15 135 125 1600 1670 545 440 50 55 64 55
MF 175 U 69 75 1.18 120 120 1420 1350 270 260 41 45 - 37
MF 180 U 79 81 1.20 105 110 1510 1305 230 200 45 46 67 49
200 Series (Low Compression Set) w/ Catalyst E (1.1%~1.25% pbw)
For more information about our product line, visit our web site at www.bluestarsilicones.com or call 1-866-474-6342.
After
Post
Cure
�High transparency
�Good mechanical
properties compromise
�Excellent extrudability
�Good thermal aging up
to 200°C
MF 240 U 44 - 1.10 70 - 1015 - 380 - 68 - 17 - �Low compression set
�High resiliency
MF 280 U 77 79 1.35 110 90 1075 1060 210 165 54 52 40 31 �Low shrinkage
300 Series (High Mechanical Properties) w/ Catalyst E (1.1%~1.25% pbw)
MF 345 U 41 45 1.10 205 180 1060 1045 560 460 45 48 - 42
MF 360 U 60 62 1.15 220 200 1320 1305 560 430 45 47 - 48
MF 370 U 65 70 1.18 250 230 1320 1350 520 440 35 36 - 52
700 Series (Very Low Compression Set) w/ Catalyst E (1.1%~1.25% pbw)
MF 750 U 51 49 1.13 73 73 1130 1280 425 445 71 68 24 18
MF 760 U 59 63 1.16 78 87 1190 1220 366 344 61 65 18 9
MF 770 U 71 73 1.18 87 78 1220 1205 312 280 56 56 8 6
Bluestar Silicones. Delivering Your Potential.
Bluestar Silicones Rhodorsil ® Bases Product Line
�High transparency
�High tear strength
�Excellent extrudability
& molding behavior
�Low compression set
�Good oil resistance
�Excellent heat stability
AD 744
- Industrial Grade
- Heat Stabilizer to
250°C
TFC 10
- Food Grade
- Heat Stabilizer to
300°C
AD 703
- Industrial Grade
- Heat Stabilizer to
300°C
HAC 5
- High Ash Cohesion
HFR 1
- High Fire Retardant
AD 717
- Plasticizer, Reduce
Crepe Hardening
AD 720
- Hot Oil Resistance
AD 721
- Improve Green
Strength