NSG 9000-6G - Harmonic Inc

More documents

Recommendations

Info

Appendix D Control Panel D.1 Using the Control Panel You can set preliminary configuration and control the NSG 9000-6G unit via its front panel. The front panel includes a control panel comprised of a Liquid Crystal Display (LCD) and six buttons as the following figure shows: LCD Display Right key Up key Ok key Esc key Down key Left key D.1.1 Control Panel Display The 2-line, 16-character control panel display shows the screens, sub-screens, sub-screen options, error messages, warnings and alarms. The control panel display is comprised of two lines: Line 1 - displays the name of the current screen/sub-screen or selected option. Line 2 - displays the parameter value and all editing tasks are performed in this line. In editing mode the cursor is blinking to indicate the selected character. D.1.2 Control Panel Screen Concept The control panel screens are organized in a hierarchical fashion to indicate that a main screen contains sub-screens and sub-screen options. You may access a sub-screen only via its main screen. The available main screens are as follows: Power Up screen - A main screen that appears as soon as the NSG 9000-6G boots up and after a thirty minutes of inactivity. The screen shows the company’s name, NSG 9000-6G type and IP address. Network Config screen - allows to access sub-screens for ETH configuration. Setup screen - allows to reset the device. Alarm screen - displays the last active alarm or warning. You can browse through the alarms to view them. Product Information screen - via its sub-screens you can view information about the NSG 9000-6G. © 2012 Harmonic Inc. 148 NSG 9000-6G, Version 2.7, Rev B
Appendix D Control Panel Using the Control Panel The following table lists the main screens, their browsing sequence, sub-screens and their options: Screen Browsing Sequence Sub-Sequence Options Network Config Down - Alarms Up - Product Info. ETH1 IP ETH2 IP Edit ETH1 Edit ETH2 Alarms Down - Setup Up - Network Config Active alarms and warnings Setup Down - Product Info. UP - Alarms Reset Reset device Product Info. Down - Network Config. Up - Setup Chassis Information DGboard Info. GbE Info. Software Information. Control panel hotkeys help Chassis SN DGBoard SN DGBoard FPGA GbE GbE FPGA Ver. Firmware Ver. D.1.2.1 Moving along the Screens To move along the screens and sub-screens of the control panel, use the following buttons of the control panel keypad: Button Explanation Up & Down • browse through the screens/sub-screens. • browse through sub-screen options. • while editing, browse through numerical characters. Left & Right while editing, move the cursor along the line. Enter • executes a selection of a screen/sub screen and of its available options. • quits an editing session and applies changes. Esc • moves up a menu level. • quits an editing session without applying changes. D.1.2.2 Hotkeys The hotkeys are a combination of up to three keys pressed simultaneously. The following table lists the available hotkeys and describes their functionality: Hotkeys and &< Enter> Explanation Moves you to the screen at the top of the sequence. © 2012 Harmonic Inc. 149 NSG 9000-6G, Version 2.7, Rev B
Page 1 and 2:
NSG 9000-6G Narrowcast Services Gat
Page 3 and 4:
Documentation Conventions This manu
Page 5 and 6:
Table of Contents 3.12.4 Configurin
Page 7 and 8:
Table of Contents Appendix D Contro
Page 9 and 10:
Chapter 1 Features and Specificatio
Page 11 and 12:
Chapter 1 Features and Specificatio
Page 13 and 14:
Chapter 2 Getting Started 2.1 Initi
Page 15 and 16:
Chapter 2 Getting Started Full Devi
Page 17 and 18:
Chapter 2 Getting Started Guideline
Page 19 and 20:
Chapter 2 Getting Started Guideline
Page 21 and 22:
Chapter 3 Configuring Platform Para
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Chapter 4 Configuring Applications
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98: Chapter 4 Configuring Applications
Page 99 and 100: Chapter 4 Configuring Applications
Page 101 and 102: Chapter 5 Conditional Access System
Page 109 and 110: Chapter 6 Monitoring and Troublesho
Page 135 and 136: Appendix A Firmware Upgrade Using a
Page 141 and 142: Appendix B Upgrade Server Installat
Page 147: Appendix C Standard ES Types and De
Page 151 and 152: Appendix D Control Panel Using the
Page 153 and 154: Appendix E EIA SDT and HRC Standard
Page 159: Harmonic Inc. 4300 North First Stre
show all

NSG 9000-6G - Harmonic Inc

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?