NSG 9000-6G - Harmonic Inc

More documents

Recommendations

Info

Appendix A Firmware Upgrade Using an External Server Upgrading Procedure The Installation Status page appears: This page informs you of the installation status. The installation status log is updated every 3 seconds during the installation. NOTE: During the installation of the new firmware, you cannot access the web client of the device. If you close and reopen the web client the Status Installation page appears. When the installation is finished, either of the following takes place: If you selected Automatic reboot, the device reboots automatically. Move to Step 16. If you selected Manual reboot, the following message appears: 15. Click OK, to complete the installation and to reboot with the new firmware version. If you click Cancel, you cancel the firmware installation and you will need to re-start the installation for the device to run with a new upgraded firmware. 16. Select Platform > Chassis > General tab and verify that the device reports the same version number as the required firmware. © 2012 Harmonic Inc. 138 NSG 9000-6G, Version 2.7, Rev B
Appendix A Firmware Upgrade Using an External Server Upgrading Procedure Verify firmware version A.2.1 Recovering from Upgrade Problems To allow recovery from incidents such as failed upgrade or corrupt configuration that causes an endless loop of reboot, use the Recovery menu included in the boot sequence. The Recovery menu is available only via a serial connection to the device. If such connection is established, you can invoke the Recovery menu by pressing when prompted at a certain point during the boot sequence: as the following picture shows: Press enter to activate Recovery menu Recovery menu You can choose one of the following menu options: • Reset Device to factory default - device reboots with factory default parameters. • Switch to backup partition - device reboots from backup partition • Temporarily disable application - for Harmonic technical support only • Continue boot process - resumes the boot process • Reboot - restarts device reboot • Enter debug shell - for Harmonic technical support only © 2012 Harmonic Inc. 139 NSG 9000-6G, Version 2.7, Rev B
Page 1 and 2:
NSG 9000-6G Narrowcast Services Gat
Page 3 and 4:
Documentation Conventions This manu
Page 5 and 6:
Table of Contents 3.12.4 Configurin
Page 7 and 8:
Table of Contents Appendix D Contro
Page 9 and 10:
Chapter 1 Features and Specificatio
Page 11 and 12:
Chapter 1 Features and Specificatio
Page 13 and 14:
Chapter 2 Getting Started 2.1 Initi
Page 15 and 16:
Chapter 2 Getting Started Full Devi
Page 17 and 18:
Chapter 2 Getting Started Guideline
Page 19 and 20:
Chapter 2 Getting Started Guideline
Page 21 and 22:
Chapter 3 Configuring Platform Para
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Chapter 4 Configuring Applications
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88: Chapter 4 Configuring Applications
Page 101 and 102: Chapter 5 Conditional Access System
Page 109 and 110: Chapter 6 Monitoring and Troublesho
Page 135 and 136: Appendix A Firmware Upgrade Using a
Page 137: Appendix A Firmware Upgrade Using a
Page 141 and 142: Appendix B Upgrade Server Installat
Page 147 and 148: Appendix C Standard ES Types and De
Page 149 and 150: Appendix D Control Panel Using the
Page 151 and 152: Appendix D Control Panel Using the
Page 153 and 154: Appendix E EIA SDT and HRC Standard
Page 159: Harmonic Inc. 4300 North First Stre
show all

NSG 9000-6G - Harmonic Inc

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?