NSG 9000-6G - Harmonic Inc
NSG 9000-6G - Harmonic Inc
NSG 9000-6G - Harmonic Inc
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Chapter 6 Monitoring and Troubleshooting<br />
Monitoring <strong>NSG</strong> <strong>9000</strong>-<strong>6G</strong> Status and Alarms<br />
6.3.4 Notification List<br />
The following table lists notifications of <strong>NSG</strong> <strong>9000</strong>-<strong>6G</strong>. A notification is a message sent from<br />
the device to the alarm log to denote a status change without raising any alarm. However,<br />
depending on the configuration, a notification issue may trigger an SNMP trap.<br />
Notification Message<br />
Active DTI Port Is/Changed<br />
to <br />
DTI Client Status Changed<br />
Corrupt Firmware File,<br />
Booting with Previous<br />
Firmware<br />
Cannot Find BOOTP Server,<br />
Booting with Previous IP<br />
Reboot System Recovered<br />
from Watchdog Reset<br />
Reboot System Recovered<br />
from Power Reset<br />
Reboot Shutdown at <br />
Configuration Error <br />
SLOT QAM-RF Module<br />
Reset by user Status=OK/<br />
Fail<br />
IpInp Manual Revert<br />
from backup port <br />
IpInp Manual Switch to<br />
backup port <br />
IpInp-X Switch to Backup<br />
Port Y<br />
IpInp-X Cannot Switch to<br />
Backup Port Y - Occupied<br />
IpInp Backup Port Y switched<br />
to Primary X<br />
Firmware File Download<br />
Failed<br />
Switched to Alternate Source<br />
GbE Card - Output Buffer<br />
Sync Byte Error<br />
IPTSIN MPEG Sync Loss<br />
TS-Out Near Overflow<br />
Clock Update Started<br />
Description<br />
The active port of the <strong>NSG</strong>'s DTI client has changed (from 1 to 2<br />
or vice-versa)<br />
The status of DTI Client has changed to the value reflected in<br />
Platform > General DTI.<br />
Could not load new firmware file to flash due to file corruption.<br />
BOOTP server did not respond within the defined time out, <strong>NSG</strong><br />
<strong>9000</strong>-<strong>6G</strong> booted with its previous IP settings.<br />
System recovered from HW Watchdog reset<br />
System recovered from power reset<br />
Shutdown at (Reboot)<br />
Configuration failed in XML validation<br />
User initiated QAM-RF reset in slot . The status is either OK<br />
or Fail.<br />
User manually reverted to the GbE input port from backup<br />
port <br />
User manually switched from GbE input port to backup port<br />
<br />
Port redundancy - switched automatically from the Primary port<br />
to the Backup port because of no bit rate at the Primary port<br />
Port redundancy - tried to automatically switch from a primary<br />
port to a backup port but the backup port was occupied.<br />
Port redundancy - switched automatically from the Backup port<br />
to the Primary port because of no bit rate at the Backup port<br />
Failed to download new firmware file using the specified path.<br />
The <strong>NSG</strong> has switched to the alternative IP/UDP source that is<br />
configured for this session<br />
GbE card detected and invalid packet.<br />
IP input traffic contains no valid MPEG data<br />
The actual output bit rate is nearing the configured QAM output<br />
bit rate.<br />
RTC clock is being updated.<br />
Displayed in<br />
Alarm Log<br />
No<br />
No<br />
© 2012 <strong>Harmonic</strong> <strong>Inc</strong>. 122 <strong>NSG</strong> <strong>9000</strong>-<strong>6G</strong>, Version 2.7, Rev B