AUTOPREP SPOT PRIMER - Globalsafetynet.com
AUTOPREP SPOT PRIMER - Globalsafetynet.com
AUTOPREP SPOT PRIMER - Globalsafetynet.com
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
TECHNICAL DATA SHEET<br />
Page 1 of 2<br />
October 2003<br />
<strong>AUTOPREP</strong> ® <strong>SPOT</strong> <strong>PRIMER</strong><br />
DESCRIPTION:<br />
Autoprep Spot Primer is a one-<strong>com</strong>ponent aerosol primer-surfacer design for spot<br />
priming of sand through and small areas. Autoprep Spot Primer provides good build<br />
while offering easy sanding and good enamel holdout for small areas.<br />
PRODUCT & ADDITIVES:<br />
PRODUCTS:<br />
BASIC RAW<br />
MATERIALS:<br />
Autoprep Spot Primer<br />
Autoprep Spot Primer: physically drying binders<br />
SUITABLE SURFACES :<br />
Autoprep Spot Primer:<br />
—Existing finishes, degreased and sanded with #P220 to #P320 grit paper dry.<br />
—Any sand through areas over premium polyester bodyfiller sanded with #P180 to<br />
#P220 grit dry.<br />
—Steel, small areas degreased and sanded with #P80 then #P120 grit dry.<br />
—Autoprep Etching Pen, let flash for 15-20 minutes then apply Autoprep Spot Primer.<br />
NOTE:<br />
Although Autoprep Spot Primer will provide adequate adhesion and protection if<br />
applied directly over bare steel or aluminum, for maximum adhesion and corrosion<br />
protection, we re<strong>com</strong>mend first applying one coat of etching primer by use of the<br />
Autoprep Etching Pen. Allow 15 - 20 minutes before the application of Autoprep Spot<br />
Primer.<br />
APPLICATION:<br />
1.<br />
Contains acrylic resins,<br />
physically drying binders and<br />
other ingredients. 4.<br />
2–5 minutes at 70°F (20°C)<br />
2.<br />
Autoprep Spot Primer ready to<br />
spray.<br />
(Shake aerosol can before use)<br />
5.<br />
30 minutes at 70°F (20°C)<br />
5 minutes with short wave<br />
infrared.<br />
3.<br />
2–4x1<br />
6.<br />
Sand and then apply sealer or<br />
topcoat.
TECHNICAL DATA SHEET<br />
Page 2 of 2<br />
October 2003<br />
<strong>AUTOPREP</strong> ® <strong>SPOT</strong> <strong>PRIMER</strong><br />
MIXING RATIO:<br />
APPLICATION<br />
METHOD:<br />
None. Product is ready to use (Shake aerosol can thoroughly before each use).<br />
Hold aerosol can approximately 5 to 7 inches from panel. Depress nozzle and apply<br />
an even coat. Allow 2-5 minutes flash-off between coats.<br />
After Application:<br />
Invert aerosol can and momentarily depress nozzle (2-3 seconds). This allows aerosol<br />
propellant to clean nozzle.<br />
RECOATABILITY: Autoprep Spot Primer can be topcoated with all Sikkens topcoats. Autoprep Spot<br />
Primer can be sealed, after sanding, with any Sikkens wet-on-wet product. Please see<br />
the TDS relative to the product chosen.<br />
DRYING TIME:<br />
FILM<br />
THICKNESS:<br />
COVER RATE:<br />
STOCK KEEPING:<br />
COLOR:<br />
CONTAINER<br />
SIZE:<br />
SHELF LIFE:<br />
Dry to Sand<br />
70°F (20°C) Infrared<br />
Three coats 30 minutes 5 minutes<br />
.6–.8 mils per single wet coat.<br />
Approximately 75 sq. ft./aerosol can of Autoprep Spot Primer per single coat.<br />
Grey<br />
14.75-ounce net weight (418 grams) aerosol can<br />
One year if stored in original container at room temperature.<br />
SAFETY ASPECTS:<br />
READY TO<br />
SPRAY VOC<br />
(In Aerosol Can): 6.1 lb/gal<br />
NOTICE:<br />
730 g/liter<br />
Do not handle until the Material Safety Data Sheets have been read and understood.<br />
Regulations require that all employees be trained on Material Safety Data Sheets for all<br />
chemicals with which they <strong>com</strong>e in contact. The manufacturer re<strong>com</strong>mends the use of<br />
an air-supplied respirator when exposed to vapors or spray mist.<br />
Aerosol Cans:<br />
Keep containers tightly closed. Isolate from heat, sparks and open flame. Closed<br />
containers may explode when exposed to extreme heat. Contents under pressure. Do<br />
not use or store near sources of heat, sparks or open flame. Keep away from any<br />
source of heat such as sunlight, heaters or stoves that could cause the container to<br />
burst. Do not puncture or incinerate. Do not crush or place in a garbage <strong>com</strong>pactor.<br />
Do not store above 120 degrees Fahrenheit/49 degrees Celsius. Aerosol containers<br />
may explode when exposed to extreme heat.