TATRAMAT - ohrievače vody, s.r.o. - META-GAS spol.sro
TATRAMAT - ohrievače vody, s.r.o. - META-GAS spol.sro
TATRAMAT - ohrievače vody, s.r.o. - META-GAS spol.sro
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
English<br />
According to the heater position that suits you best, establish<br />
the ragbolts so that they are in a horizontal position, with a<br />
distance from each other according to the dimension table,<br />
and with the screwed part protruding as much as 20 mm from<br />
the wall. Hang the heater directly on the bolts and using the<br />
washers and nuts, bring it close to the wall. Because the heater<br />
must be fastened to the wall by nuts, it can not be installed in an<br />
interior corner.<br />
A drain plug shall be installed before the safety valve through<br />
the T- joint (T-fitting) for servicing purposes.<br />
Drain plug<br />
With ELOV x.1, LOVK x.1, LOVK 120, LOVK 150, ELOV 200<br />
and LOVK 200 type heaters put the heater on the suspension<br />
arches so that the imaginary flow-line of the connection<br />
mouthpiece openings through the heater axle is parallel to the<br />
wall on which the heater is suspended. (See Fig. No. 7 on Page<br />
4, Position No. 6.)<br />
Safety valve<br />
T- joint<br />
5. CONNECTION TO WATER SUPPLY PLUMBING<br />
Connection to the water supply plumbing can be performed by a competent specialist only, where the installation shall<br />
correspond to the valid standards and to the regulations and requirements presented in the manual.<br />
It is recommended to place the heater, as closely as possible, in the place most often used for hot water intake. It is<br />
prohibited to connect the heater to the water distribution network without a safety valve. Between the heater and the<br />
safety valve there should not be any closing armatures inserted. Safety valve installation and operation need to be<br />
provided for according to the instructions given in the safety valve Operation Manual. The safety valve function should be<br />
checked once a month during the heater's operation period and after each interruption of operation lasting more than 5<br />
days. At water overpressure of more than 0.6 MPa in the pipeline system a reduction valve must be inserted before the<br />
safety valve, so that the safety valve should steadily retain the overpressure increase in the sewage pipe of the<br />
distribution system. The water passing through the safety valve during heating shall be diverted in the appropriate<br />
manner into the sewage piping.<br />
For horizontal boilers of the LOVK x.1 type the circulation need to be inserted into the heat exchanger of the circulation<br />
heating water circuit. In order to remove possible sludge, rinse out the heat exchanger prior to the heater-with-heatexchanger<br />
installation to the circulation heating water distribution.<br />
1,2<br />
3<br />
4<br />
5<br />
6<br />
7<br />
8<br />
9<br />
10<br />
K<br />
Č<br />
- mixing plumbing fixtures<br />
- water heater<br />
- safety valve with backflow valve<br />
- manometer<br />
- water pipe line stop valve<br />
- central heating stop valve<br />
- drain plug<br />
- backflow valve (if it is not in the<br />
safety valve)<br />
- reducing valve<br />
- central heating boiler<br />
- pump<br />
30<br />
6. HEATER CONNECTION TO THE ELECTRICAL NETWORK<br />
Specialists should be entrusted with the installation and electric connection who have<br />
corresponding authorization and who shall guarantee all safety requirements related to<br />
installation and operation.<br />
The electric installation shall correspond to the applicable regulations and standards. A heater with a fixed network<br />
attachment must have a switch in this connection having contact distances that provide total heater disconnection from<br />
the electrical network in all poles of over-voltage category No. III.Aheater with a movable supply network attachment with