cross section crash boxes

More documents

Recommendations

Info

Figure 6.22.(cont.) (c) Figure 6.23. Cross-section pictures of deformed empty and F1 foam filled 1050 H14 G1 box with montage parts, t=3 mm. 124
Load–displacement and mean load-displacement curves of empty and G1 and G2 filled crash boxes are shown in Figures 6.24 and 6.25, respectively. It is seen in Figure 6.24 that foam filling has almost no effect on the deformation load until about the complete deformation of the corrugated section. Following the crushing of the corrugated section, partially filled crash boxes with montage parts show higher deformation loads than empty boxes. Increasing the relative density of the foam filler slightly increases the deformation load values. Similar effects of foam filling are also seen on the mean load-displacement graphs of filled boxes, Figure 6.25. Similar to the crash boxes without montage parts, the SEA values of partially filled crash boxes are lower than those of empty box until about a critical displacement (Figure 6.26). The critical displacement for both geometries is found to depend on the box thickness. The critical displacement for SEA becoming effective is about 45 mm in 3 mm thick crash box, 40 mm for 2.5 mm thick boxes and 60 mm for 2 mm thick boxes. It is further noted that the effective SEA range for boxes with montage parts is narrower than the boxes without montage parts. (a) Figure 6.24. Load-displacement graphs of G1 and G2 empty and filled crash boxes with a) 3 mm, b) 2.5 mm and c) 2 mm thickness. (cont. on next page) 125
Page 1 and 2:
OPTIMIZATION OF THE AXIAL CRUSHING
Page 3 and 4:
ACKNOWLEDGEMENTS My PhD quest has b
Page 5 and 6:
ÖZET KAPALI HÜCRELİ ALUMİNYUM K
Page 7 and 8:
CHAPTER 4 EXPERIMENTAL DETAILS ....
Page 9 and 10:
CHAPTER 8 ALUMINUM CRASH BOX OPTIMI
Page 12 and 13:
Figure 3.7. Simulations of the defo
Page 14 and 15:
Figure 4.9. Dimensions of tensile t
Page 16 and 17:
Figure 6.21. Sequential deformation
Page 18 and 19:
Figure 7.20. Sequential deformation
Page 20 and 21:
LIST OF TABLES Table Page Table 4.1
Page 22 and 23:
Figure 1. 1. The body in white stru
Page 24 and 25:
Figure 1. 4. Commercial crash boxes
Page 26 and 27:
CHAPTER 2 AL CLOSED CELL FOAMS: PRO
Page 28 and 29:
The processing methods and mechanic
Page 30 and 31:
Figure 2. 5 The preferred particle
Page 32 and 33:
Figure 2. 8. Typical cellular struc
Page 34 and 35:
Figure 2. 10. Manufacturing cost of
Page 36:
Figure 2. 12. Laser assisted foamed
Page 41 and 42:
Figure 2.16. Shear strength, normal
Page 43 and 44:
Figure 2. 19. Yield strength vs. re
Page 45 and 46:
Figure 2. 21. Unit cell geometry an
Page 47 and 48:
Figure 2. 24. Load-displacement cur
Page 49 and 50:
Figure 2. 26. The photographs of a
Page 51 and 52:
CHAPTER 3 CRUSHING BEHAVIOR OF TUBU
Page 53 and 54:
Figure 3.2. Diamond deformation mod
Page 57 and 58:
deformation mode transition from ax
Page 59 and 60:
Figure 3.8. Energy absorption of qu
Page 61:
(a) (c) Figure 3.10. Deformation mo
Page 65 and 66:
(a) (b) Figure 3.13. a) Schematic o
Page 67 and 68:
(a) (b) (c) Figure 3.15. a) Load-di
Page 72 and 73:
Figure 3.18. The crush terminology.
Page 75 and 76:
The quasi-static compression behavi
Page 77 and 78:
Figure 3.22. The variation of speci
Page 79 and 80:
Figure 3.24. Deformation modes of e
Page 81 and 82:
Figure 3.27. SEA values of empty an
Page 83 and 84:
Figure 3.29. (cont.) 3.5. Motivatio
Page 85 and 86:
CHAPTER 4 EXPERIMENTAL DETAILS 4.1.
Page 87 and 88:
(a) (b) Figure 4.3.Pictures of a) f
Page 89 and 90:
oxes are shown in Figure 4.6. The l
Page 91 and 92:
Figure 4.7. The method of trigger m
Page 93 and 94: 4.4. Compression Tests of Crash Box
Page 95 and 96: 4.5.2. Uniaxial Compression Testing
Page 97 and 98: Table 4.1 (Cont.) G1 T3 F2 G1T3F2 3
Page 99 and 100: Table 4.2 (Cont.) G1 T2.5 WP F2 G1T
Page 101: CHAPTER 5 SIMULATION AND OPTIMIZATI
Page 105: considered in axial and transverse
Page 109 and 110: were constrained. Since the width o
Page 116 and 117: 5.4. The Crashworthiness Optimizati
Page 118 and 119: great effect on the crushing behavi
Page 120: CHAPTER 6 EXPERIMENTAL RESULTS 6.1.
Page 124 and 125: Figure 6.3.Tensile stress-strain cu
Page 126 and 127: (a) (b) Figure 6.5. Sequential defo
Page 128 and 129: plate (Figure 6(b)). The trigger is
Page 130 and 131: (a) (b) Figure 6.9. Deformation seq
Page 132 and 133: Figure 6.12. Sequential deformation
Page 138 and 139: Figure 6.18. (cont.) (c) (a) (b) Fi
Page 140 and 141: Figure 6.20.(cont.). (b) (c) 6.5.4.
Page 142 and 143: Figure 6.21.(cont.) (b) (c) 122
Page 146 and 147: Figure 6.24.(Cont.) (b) (c) (a) Fig
Page 148 and 149: Figure 6.26.(cont.) (b) (c) 6.6. Dy
Page 150 and 151: Figure 6.27. (cont.) (b) (c) 130
Page 152 and 153: CHAPTER 7 MODELING RESULTS OF FOAM,
Page 154 and 155: experimental tensile stress-strain
Page 156 and 157: significant effect of weld seem ope
Page 158 and 159: Figure 7.7. Deformation photo of fi
Page 160 and 161: Figure 7.11. Deformation photos of
Page 162 and 163: (a) (b) (c) Figure 7.14. Load-displ
Page 164 and 165: 7.4. Simulation of Empty and Partia
Page 166 and 167: Figure 7.16. (cont.) (c) (a) Figure
Page 168 and 169: (a) (b) Figure 7.18. Sequential def
Page 170 and 171: Figure 7.19. (cont.) (b) (c) 150
Page 172 and 173: Figure 7.20. (cont.) (c) (a) Figure
Page 178: (a) (b) Figure 7.26. Experimental a
Page 182 and 183: The constructed response surface of
Page 184: Table 8.1. R 2 , Radj 2 and RMSE va
Page 187 and 188: (a) (b) Figure 8.7. Response surfac
Page 189 and 190: an empty tube wall thickness higher
Page 192 and 193: where, K is a dimensionless constan
Page 194 and 195:
The dynamic simulation and analytic
Page 196:
Figure 9.4. (cont.) (c) (d) Figure
Page 199 and 200:
Figure 9.6. (cont.) (c) (d) (a) Fig
Page 203 and 204:
Equation 9.7 can also be rewritten
Page 206:
(a) (b) Figure 9.10. Energy-absorbi
Page 209 and 210:
Figure 9.11. (cont.) (d) The variat
Page 211 and 212:
foam filling were evaluated. The re
Page 213 and 214:
13. The interaction between foam fi
Page 215 and 216:
Arora, J. S.,2004,Introduction to O
Page 217 and 218:
Dannemann, K. A. and Lankford, J.,
Page 219 and 220:
Hall, I. W., Guden, M. and Yu, C. J
Page 221 and 222:
Kim, D-K. and Lee, S., 1999, Impact
Page 223 and 224:
Mamalis, A. G., Manolakos, D. E., I
Page 225 and 226:
Pugsley, A. G. and Macaulay, M., 19
Page 227 and 228:
T. Miyoshi, M. Itoh S. Akiyama A. K
Page 229:
Zhao, H., Elnasri, I. and Girard, Y
show all

cross section crash boxes

Create successful ePaper yourself

Delete template?

Save as template?