road racing fim superbike & supersport world championships & fim ...

More documents

Recommendations

Info

The original homologated fuel injection system must be used without any modification. The fuel injectors must be stock and unaltered from the original specification and manufacture. Bell mouths must remain as originally produced by the manufacturer for the homologated motorcycle. Butterfly valves cannot be changed or modified. Variable intake tract devices cannot be added if they are not present on the homologated motorcycle and they must remain identical and operate in the same way as the homologated system. All the parts of the variable intake tract device must remain exactly as homologated. Air and air/fuel mixture can go to the combustion chamber exclusively through the throttle body butterflies. Electronically controlled throttle valves, known as ‘ride-by-wire’, may be only used if the homologated model is equipped with the same system. Software may be modified but all the safety systems and procedures designed by the original manufacturer must be maintained. 2.6.8.2 Cylinder Head No modifications are allowed. No material may be added or removed from the cylinder head. The gaskets may be changed. The valves, valve seats, guides, springs, tappets, oil seals, shims, cotter valve, spring base and spring retainers must be as originally produced by the manufacturer for the homologated motorcycle. Only normal maintenance interventions as prescribed by the Manufacturer in the service manual of the motorcycle are authorised. Valve spring shims are not allowed. 2.6.8.3 Camshaft No modifications are allowed. 110 S S T
At the technical checks: for direct cam drive systems, the cam lobe lift is measured; for non direct cam drive systems (i.e. with rocker arms), the valve lift is measured. The timing of the camshaft is free, however no machining of the camshaft sprocket is authorised. 2.6.8.4 Cam sprockets or gears No dimensional modifications are allowed. 2.6.8.5 Cylinders No modifications are allowed. 2.6.8.6 Pistons No modifications are allowed (including polishing and lightening). 2.6.8.7 Piston rings No modifications are allowed. 2.6.8.8 Piston pins and clips No modifications are allowed. 2.6.8.9 Connecting rods No modifications are allowed (including polishing and lightening). 2.6.8.10 Crankshaft No modifications are allowed (including polishing and lightening). 2.6.8.11 Crankcase / Gearbox housing Crankcases must remain as homologated. No modifications are allowed (including painting, polishing and lightening). It is not allowed to add a pump used to create a vacuum in the crankcase. If a vacuum pump is installed on the homologated motorcycle then it may be used only as homologated. 111 S S T
Page 1 and 2:
ROAD RACING FIM SUPERBIKE & SUPERSP
Page 3 and 4:
FEDERATION INTERNATIONALE DE MOTOCY
Page 5 and 6:
TABLE OF CONTENTS GENERAL UNDERTAKI
Page 7 and 8:
AMENDMENTS TO THE FIM ROAD RACING S
Page 9 and 10:
1. SPORTING REGULATIONS 1.1 INTRODU
Page 11 and 12:
h - The name, address and telephone
Page 13 and 14:
FIM Safety Officer Responsible for
Page 15 and 16:
1.5 INTERNATIONAL JURY 1.5.1 The ma
Page 17 and 18:
1.7 THE FIM STEWARDS 1.7.1 There wi
Page 19 and 20:
1.11 ENTRIES 1.11.1 Each team, must
Page 21 and 22:
The riders will be previously infor
Page 23 and 24:
1.13.2 The above schedule can only
Page 25 and 26:
1.15.3 Motorcycles 1.15.4 Lap time
Page 27 and 28:
1.16.2 Participants - Constant Wet
Page 29 and 30:
1.18.2 The length of a race may onl
Page 31 and 32:
Only one generator per motorcycle m
Page 33 and 34:
On returning to the grid the riders
Page 35 and 36:
The rider must respect the speed li
Page 37 and 38:
3) Riders should use only the track
Page 39 and 40:
1.23 PIT STOPS Any rider who exceed
Page 41 and 42:
• Yellow and Red Striped Flag The
Page 43 and 44:
• Red Flag and Red Lights When th
Page 45 and 46:
1.26 FINISH OF A RACE AND RACE RESU
Page 47 and 48:
1.27.4 If the results calculated sh
Page 49 and 50:
1.30.3 For Constructors, only the h
Page 51 and 52:
After the last control: - the winni
Page 53 and 54:
2) The 3 % nitric acid test (titani
Page 55 and 56:
The Official Supplier shall provide
Page 57 and 58:
As a first step, the weight handica
Page 59 and 60:
Should the average value of ‘even
Page 61 and 62:
The stickers will be handed to the
Page 63 and 64: • Electronically controlled throt
Page 65 and 66: If the air restrictor size is not u
Page 67 and 68: 2.4.8.7 Piston rings Piston rings m
Page 69 and 70: The number of gears must remain as
Page 71 and 72: • Ram air tubes or ducts running
Page 73 and 74: 2.4.10 Main frame and pre-assembled
Page 75 and 76: Holes may be drilled on the frame o
Page 77 and 78: 2.4.10.4 Rear suspension unit Rear
Page 79 and 80: Brake discs may be altered or repla
Page 81 and 82: Fuel tanks with tank breather pipes
Page 83 and 84: k) Material of construction of the
Page 85 and 86: • License plate bracket. • Tool
Page 87 and 88: At any time during the event, the w
Page 89 and 90: The tyres used in the free practice
Page 91 and 92: • Butterflies cannot be changed o
Page 93 and 94: 2.5.8.7 Piston rings Piston rings m
Page 95 and 96: Clutch springs may be changed. The
Page 97 and 98: 2.5.9 Electrics and electronics Ele
Page 99 and 100: Once the assembly of the replacemen
Page 101 and 102: 2.5.10.3 Rear fork (swing arm) The
Page 103 and 104: Front and rear brake pads may be ch
Page 105 and 106: g) The original air ducts into the
Page 107 and 108: 2.5.10.13 Rear Safety Light All mot
Page 109 and 110: Where breather or overflow pipes ar
Page 111 and 112: 2.6.5 Number plate colours The back
Page 113: During practices, qualifying sessio
Page 117 and 118: Clutch springs may be changed. 2.6.
Page 119 and 120: Central unit (ECU) may be relocated
Page 121 and 122: The sides of the frame-body may be
Page 123 and 124: Rear suspension linkage must remain
Page 125 and 126: Handlebars and hand controls may be
Page 127 and 128: g) The lower fairing must to be con
Page 129 and 130: • Instruments, instrument bracket
Page 131 and 132: Benzene % v/v 1.0 EN 238 RVP kPa 90
Page 133 and 134: 2.7.5 Fuel Sampling and Testing 1)
Page 135 and 136: The organiser must have fire exting
Page 137 and 138: In the inspection areas, under the
Page 139 and 140: If the helmet is clearly defective,
Page 141 and 142: Dry Superpole Each motorcycle which
Page 143 and 144: During practice days: From 08h30 un
Page 145 and 146: 2.11.6 Noise control Due to the sim
Page 147 and 148: PRACTICE OR RACE N°: FIM ROAD RACI
Page 149 and 150: SPORTS PRODUCTION C 145
Page 151 and 152: NUMBERS/NUMEROS O 147
Page 153 and 154: 149
Page 155 and 156: 3. DISCIPLINARY AND ARBITRATION COD
Page 157 and 158: - any corrupt or fraudulent act, or
Page 159 and 160: 3.3.4.2 Procedures The names of the
Page 161 and 162: 2. To the CDI against a decision of
Page 163 and 164: Teams and riders contracted to comp
Page 165 and 166:
3.5.3 Witnesses and Experts 3.5.4 J
Page 167 and 168:
3.8 Law of Mercy The Management Cou
Page 169 and 170:
5. MEDICAL CODE 5.1 INTRODUCTION Th
Page 171 and 172:
• Can recommend to the Race Direc
Page 173 and 174:
Any rider, who, after treatment by
Page 175 and 176:
• Vehicles type A are to be place
Page 177 and 178:
• Equipment to immobilise limbs a
Page 179 and 180:
Medical Equipment: • Airway manag
Page 181 and 182:
• Vehicle(s) type C (number as pe
Page 183 and 184:
5.4 MEDICAL MALPRACTICE INSURANCE A
Page 185 and 186:
6. ANTI-DOPING CODE The regulations
Page 187 and 188:
TECHNICAL REGULATIONS APPENDIX 2013
Page 189 and 190:
• At the latest within 3 days bef
Page 191 and 192:
• Right side cover, Left side cov
Page 193 and 194:
• ABS installation and its compon
show all

road racing fim superbike & supersport world championships & fim ...

Create successful ePaper yourself

Delete template?

Save as template?