Power Analysers & Recorders cont'd. - Ferret

ELECTRICAL POWER
Power Analysers & Recorders cont’d.
Hioki 3332 Power HiTester Suitable for Standby Power Single Phase
HIO,3332 POWERTESTER (8776) AU
Suitable for measuring very low effective power, for stand -by mode of home
equipment. Ultra high-sensitive measurement. Use to measure effective
power of equipment in standby mode: Current 1mA with 0.1μA resolution.
Wide Measurement range, up 5A direct input and auto range facilities are
available. Suitable for single-phase/two wire power measurement. Voltage
measuring ranges from 15V to 600V six ranges, Power 15mW to 30kW 90
ranges. Integration range 0 to ± 999999MAh/MWh, integration time up to
10,000 hours. RS232C interface. Other features includes measurement of
inrush current during device start-up, measurement of standby power under
1W, precise calculations of minute stand by power, when 150V/1mA range is
selected, integration from ± 000.000mWh can be performed. Low numbers/
units are automatically switched to a 6 digit display, allowing measurement in
high resolution.
LEM Topas 1000
Power Network Analyser
LEM,TOPAS1000 (8762) AU
Measures all relevant parameters in one
measurement system. Inputs (isolated) voltage
4 channels, 200mV to 1kV, current 4 channels,
supplied with 4 x 0 to 10A, 10 to 100A AC
clamp-on CTs and 4 x (unit powered) 0 to 3kA LEM-Flex current sensors.
Can be configured for 8 voltage channels. Measuring functions RMS, V(U)
voltage imbalance, positive, negative & zero phase sequence, phasor (vector)
diagrams, amps (I)a, pf, kVA, kVAr, f(Hz), energy, on-line oscilloscope, power
and multimeter, harmonics (by power/direction, magnitude & phase), interharmonics,
THD, flicker, transients (100kHz to 10MHz), will capture events
from 0.1μs in duration. Software configured manual or auto trigger levels,
ethernet or serial interface, memory >540Mb/HDD.
Megger MMC850 Multi/Single Core AC
Clampmeter - 200 Amps
MEG,MMC850CLAMPMETER (8776) AU
Multi/Single Core AC. Clampmeter single, two or three core
cable measurement. Flat or round section cables; no need
to split wires. Measures up to 200A on single-core, 100A on
multi-core cables. Cable centralising clamp, backlit display,
50Hz and 60Hz supplies, IEC 1010-2-032, CAT III 600V
safety protection.
Megger SK-MDP3 Distribution
Profiler 1000Amps/35kV
MEG,SK-MDP3 (8727) AU
Records currents up to 1,000A, plus 200A over-range.
Waveform capture and harmonic analysis up to the 32nd
order. Power factor/power and relative voltage RMS
magnitude, overhead line spring attachment, accurate data
capture via advanced MDP software, Lightweight battery
operated, weather resistant. Easy plug-in for quick data
retrieval.
MET,MX2040 (8811) AU
Measures A, V, Hz, kW, kVA, kVAR, kWH, PF and resistance.
Ranges 200A & 2kA, 600V & 1kV, 20, 200kW & 2MW &
kWH. Scale length 3,000. 1 & 3ph operation. Motor rotation
indication. Peak, min, max, average, RMS, and crest factor
indication. Peak response time 1μs. Analogue output option
fitted giving dynamic signals and calculated parameters
(energy, etc). Jaw opening 55mm for 22 x 64 bars.
36
Power Analysers & Recorders cont’d.
Metrosonics PF-1-F Overhead Profiler
MET,PF-1-F (8726) AU
Distribution line profilers for current measurement on power lines. Logs current
consumption to internal memory. Set of 3 profilers with one display module.
Windows software included. Current range 5 to 1,000A. Resolution 1A.
Accuracy 1.5% ±5A. Conductor voltage to 69kV nominal. Sample rate 1s to
10min. Memory 64k readings. Data storage modes: stop when full or wrap
around. Data retention after low battery shutdown 30d. Min conductor spacing
600mm.
AC Electrical Chart Recorders
Hioki 9132 Clip-on AC Current Transducer
HIO,9132 (8604) AU
Ranges 20 to 1kA fs. Short term overload capability 2kA. Output 0.2VAC. For
use with Hioki 8800 series recorders, for current waveform recording.
Current Clamp Probes & Accessories
See also Electrical Testers on page 29 & 30
See also Power Analysers & Recorders on page 32-36
www.techrentals.com.au
CHK 3 Phase Converter for CTs 1A Input to 200mA Output
CHK,CK1 (8791) AU
Adaptor for CTs with 1A secondary outputs, this unit suits CHK,PM30/20.
CHK 3 Phase Converter for CTs 5A Input to 200mA Output
CHK,CK5 (8785) AU
Adaptor for CTs with 5A secondary outputs, unit suits CHK,PM30/20.
CHK CR100 Clamp-on CT
CHK,CR100 (8782) AU/MY
Jaws 43mmØ inside. Use with CHK,PM20 or PM30 for use as fourth CT to
measure neutral current. Accuracy Class 1.
CHK CR500 Clamp-on 500 CT
CHK,CR500 (8789) AU
Jaws 43mmØ inside. Use with CHK,PM20 or PM30 for use as fourth CT to
measure neutral current. Accuracy Class 1.
CHK CT1000L Large 1kA Primary Clamp-on CT
CHK,CT1000L (8796) AU
Large 123 x 35mm 1kA primary clamp-on CT for CHK,PM20/30.
CHK CT3000L Large 3kA Primary Clamp-on CT
CHK,CT3000L (8790) AU
Large 123 x 35mm 3kA primary clamp-on CT for CHK,PM20/30.
Dranetz Communications Adapter
- Fibre to Ethernet with Node Link
Software
DRA-BMI,CAF-ETHERNET (8709) AU
Communications Adapter-Fibre to Ethernet
with NodeLink Software and Moxa
Networking Software for the following
Dranetz-BMI Models: DRA-BMI,PX5, DRA-
BMI, PX5-400, DRA-BMI,PG4400.