Power Analysers & Recorders cont'd. - Ferret

ELECTRICAL POWER
Micro-Ohm Meters & Earth Testers
cont’d.
Megger DLRO200 200A Micro-Ohm Meter
MEG,DLRO200 (1265) AU
Test currents from 10A to 200ADC. 0.1 microohm
resolution. Weight 14.5kg On board memory for
up to 300 test results and notes. RS232 download
of stored results onto PC or printer.
Megger DLRO600 Digital Micro-Ohm Meter - High current
MEG,DLRO600 (1268) AU/MY
currents from 10A to 600A subject to the load resistance and supply voltage.
A large backlit liquid crystal display provides all the information needed to
perform a test; all test parameters and measurement results are displayed.
Accuracy: Voltage ±0.5% ± 0.1mV. Current ±0.5% ± 0.1A. Resistance:
detail]. Power supply for: full output: 207 to 265V 50/60Hz with a load less than
load]. Reduced output: Down to 100V 50/60Hz [refer to data sheet for detail].
Test Current Range: 10A to 600A unsmoothed DC in 1A steps. Accuracy:
±2% ±2A. Test Modes: Manual, Auto, Continuous. Test Time: 7 seconds
normal /auto mode. Refreshed every 2 seconds in continuous mode. Voltmeter
input impedance: >200kW. Data Transfer: Real time or batch download
via RS232 using AVO Download Manager. Storage Capacity: 300 result sets.
Megger DLRO Wind Turbine
Lightning
Protection Test Lead Set
MEG,DLRO-100LEAD (1263) AU
For Megger DLRO 10 series digital microohm
meters. Specially designed for measuring
resistance of lightning protection circuit between
wind turbine blade tip and ground. Kelvin clip
and hook ends on 100m cable reel. 5m DH2
lead with duplex hand spikes and hook end.
Megger DLRO lead set Current & Voltage Leads
MEG,DLRO-LEADSET (1263) AU
For Megger DLRO digital micro-ohm meters potential spike lead set x2 and
current clip lead set x2. Leads are used to separate the C & P connections.
This avoids the erroneously high readings taken due to a high resistance
contact. Current clip lead set 2m (242041-7) and Potential Spike set 2m
(242021-7).
Megger LT330 Non-tripping Loop Tester, 3Ph Safe,
1ph or ph-ph
MEG,LT330 EN-AU (8445) AU
Non-tripping loop tester. 3 phase safe, single or phase-phase loop testing. 2
wire test (high current). Single phase loop testing. Phase - Phase loop testing.
L-N-E polarity indicators. PFC display. Phase rotation indicator. Frequency
storage & download via USB. IP54 weatherproof. IEC61010-1 300v CAT III.
EN61557.
T&R DSM200 200A Micro-Ohm Meter
T&R,DSM200 (1264) AU
with RS232 output. AC mains operation. Complete with 3m leads.
Save your time and reduce your real costs.
Find out all
solutions on page 11.
32
www.techrentals.com.au
Power Analysers & Recorders
See also Current Clamps Probes & Accessories on page 36-38
CCI Power-Mate 15A Single Phase
Power/Energy Measurements
CCI,POWER-MATE 15A (8803) AU
Can accurately measure and calculate power, volts, amps and
energy being used by an electrical appliance. Also measures
the greenhouse gas emission created by an appliance. Can
determine the actual running cost, how much energy the
appliance used in kilowatt-hours and how many kilograms of
greenhouse gas emissions it produced all in hourly, yearly,
quarterly and accumulated figures. Features an LED display for easy reading
and high visibility at all times. 15 amp version - to a maximum continuous
capacity of 15A, but readings are accurate to 18A and the cable is rated to
15A. Provides a variety of measurements including: power in watts, voltage
and current. Provides the minimum, maximum as well as instantaneous
readings.
CHK PM20 Power Quality
Analyser/Logger
CHK,PM20 MY
Three phase, weatherproof IP65 field unit. Three voltage
channels 63 to 440V (isolated). Four current
channels 0 to 3kA RMS (3ph & neutral). Supplied with
3 x 1kA clamp-on CTs (cable capacity 50mm), 3kA
for large conductors and 500A for neutrals clamp-on
CTs are available. Memory 4Mb. In-built 2 line LCD
display. Records V, A, pf, f(Hz), kW, kVA, kVAr, THD, total energy and tariffs,
high speed RMS waveform capture events outside preset limits (10ms intervals).
Software provides graphs and summaries to PC. Download files while
logging. RS232 interface. PC using Win 95, 98 or NT4 O/S, is required with the
CHK POWERview software to configure this unit before operating.
CHK Gridsense PM30 3 Phase
Powermonic Power Logger
CHK,PM30 (8788) AU/MY
Weatherproof IP65 field unit. Channels 3 voltage, 63
to 440V (isolated), 4 current 0 to 3kA (3ph & neutral)
RMS. Supplied with 3 x 1kA clamp-on CTs (cable
capacity 50mm). Clamp-on CTs of 3kA, 1kA for large
conductors and 500A & 100A for neutral conductor
current measurement are available. Memory 4Mb.
In-built 2 line LCD display. Records V, A, pf, f(Hz), kVA, kVAr, kW, harmonics,
(THD and individual to 48th). Total energy, tariffs, max demands, transient
and sub-cycle disturbances. Software provides graphs and summaries to PC.
Download files while logging via RS232 interface. PC using Win 95, 98, NT4,
2000, XP, O/S, is required with the CHK POWERview software to configure
this unit before operating.
CHK Gridsense PM30
Plus 3 Phase Powermonic Logger
CHK,PM30PLUS (8778) AU/MY
Weatherproof IP65 field unit. Channels: 3 Voltage,
63 to 440V (isolated). 3 current 30 to 3,000A (3ph)
rms. Supplied with 3 flexible 3,000A clamp-on CTs
(flexible CT length 600mm and 190mmØ). (In addition,
clamp-on CTs of 3,000A, 1,000A for large conductors
and 500A and 100A for neutral conductor current
measurement are available.) Memory: 4Mb. Inbuilt
two line LCD display. Records: V, A, pf, f(Hz), kVA,
kVAr, kW, harmonics, (THD and individual to 48th). Total energy, tariffs,
maximum demands, transient and sub-cycle disturbances. Included software
provides graphs and summaries to PC. Download files while logging RS-232
interface. A PC using Windows 95, 98, NT4, WIN2000 or XP O/S, is required
with the CHK POWERview software to configure this unit before operating.