UltraVoice Manual - Alerting & Notification
UltraVoice Manual - Alerting & Notification UltraVoice Manual - Alerting & Notification
Federal Signal UltraVoice Installation and Operation Manual Table 5 - Wiring example for four DSA3 speaker arrays Terminal Number Wire Color Drivers Array JP21-1 White/Brown A,B DSA3 #1&2 JP21-2 Brown A,B DSA3 #1&2 JP22-1 White/Brown A,B DSA3 #3&4 JP22-2 Brown A,B DSA3 #3&4 JP23-1 White/Red C DSA3 #1&2&3&4 JP23-2 Red C DSA3 #1&2,&3&4 Notes: 1. The Brown wires from the first two DSA arrays must be tied together and connected to JP25-2. Likewise, the White/Brown wires from the first two DSA arrays must be tied together and connected to JP25-1. Repeat this procedure for the second two DSA arrays and connect to JP26. 2. a. Connect the White/Red wire from DSA3 #1 to the Red wire from DSA3 #2. b. Connect the White/Red wire from DSA3 #3 to the Red wire from DSA3 #4. c. Connect the Red wires from DSA3 #1 and #3 together and jumper to JP23-2. d. Connect the White/Red wires from DSA3 #2 and #4 together and jumper to JP23-1. Note: See appendix A for drawing examples. INSTALLATION 40
D. UVT6048 Inter-Cabinet Wiring 1. Route 1” flexible conduit between the two (2) top cabinets. 2. Route the supplied 22 AWG white wire attached to the charger (-) output in the secondary control through the conduit and butt splice or wire nut to the 22 AWG white wire attached to the charger (+) output in the primary control cabinet. 3. Route both 22 AWG orange wires in the secondary control cabinet through the conduit to the primary control cabinet. Wire one orange wire from the secondary cabinet to JP15 position 4. Connect the other orange wire from the secondary cabinet to the orange wire coming from the intrusion switch in the primary battery cabinet with a butt splice or wire nut. 4. Route the supplied six (6) conductor cable through the conduit and attach one end to JP18 of the primary control cabinet and the other to JP29 on the secondary control cabinet. 5. Route the supplied 4 AWG black wire through the conduit and land on the (-) stud of both motherboards. Make sure the nuts are on tight taking care not to damage the motherboard. Federal Signal UltraVoice Installation and Operation Manual INSTALLATION 41 E. Battery Hookup DANGER When installing or removing batteries, take care to avoid shorting battery terminals to the metal battery cabinet. Failure to do so could result in serious personal injury or death. Batteries miswired can cause serious personal injury or death. Read and understand the following information before making actual connections. The end user must obtain batteries to install in the lower cabinet(s) as listed in the specifications section of this manual. Wire batteries as follows: 1. Remove the accessory kit from the battery box. 2. Connect the wires as shown in the appropriate system wiring diagram for the model of UltraVoice purchased; 259024 (2-way models), 259025 (1way models), or 259027(UVT6048) as appropriate. 3. Apply silicon grease to battery terminals after wiring to prevent corrosion. F. Optional Connections Refer to Section 8 for optional equipment connections and setup. See wiring diagram appendix B for field wiring of the 6048 models.
- Page 1 and 2: UltraVoice tm Electronic Siren Cont
- Page 3 and 4: Federal Signal UltraVoice Installat
- Page 5 and 6: Federal Signal UltraVoice Installat
- Page 7 and 8: SECTION IX - APPENDIX A Federal Sig
- Page 9 and 10: Activation codes, command sequences
- Page 11 and 12: Site Address Switch: Unit Address T
- Page 13 and 14: Delay The delay function causes the
- Page 15 and 16: 2.0 Electrical Federal Signal Ultra
- Page 17 and 18: 2.4 Radio Communication Federal Sig
- Page 19 and 20: Federal Signal UltraVoice Installat
- Page 21 and 22: Controls: Federal Signal UltraVoice
- Page 23 and 24: 2.12 Audio Output to Amplifiers Fed
- Page 25 and 26: Federal Signal UltraVoice Installat
- Page 27 and 28: functions programmed for that code,
- Page 29 and 30: 4.0 Control Unit The information in
- Page 31 and 32: Federal Signal UltraVoice Installat
- Page 33 and 34: 6. Drill a 3/8" pilot hole at each
- Page 35 and 36: 6. Install a user-supplied, fused,
- Page 37 and 38: Table 2 - MOD6048 Speaker Wiring Fe
- Page 39: Speaker Wiring for DSA Series Siren
- Page 43 and 44: Federal Signal UltraVoice Installat
- Page 45 and 46: Federal Signal UltraVoice Installat
- Page 47 and 48: Federal Signal UltraVoice Installat
- Page 49 and 50: 5.4 Yagi Antenna Installation Yagi
- Page 51 and 52: Note A: Objects around the antenna
- Page 53 and 54: Federal Signal UltraVoice Installat
- Page 55 and 56: Federal Signal UltraVoice Installat
- Page 57 and 58: Federal Signal UltraVoice Installat
- Page 59 and 60: 7.0 General WARNING Service or main
- Page 61 and 62: C. Battery Check 1. The voltage of
- Page 63 and 64: 8. Turn service monitor to .25 V RF
- Page 65 and 66: 7.4 Adjustment Procedure for a Two-
- Page 67 and 68: Federal Signal UltraVoice Installat
- Page 69 and 70: 8.0 Radio Control The siren can be
- Page 71 and 72: instructions in the programming sof
- Page 73 and 74: Amplifier status for each amp in th
- Page 75 and 76: Example DTMF Report String Federal
- Page 77 and 78: Federal Signal UltraVoice Installat
- Page 79 and 80: 8.11 FS-SINAD Option Federal Signal
- Page 81 and 82: Indicators Federal Signal UltraVoic
- Page 83 and 84: 8.13 UV6048 Satellite Models Federa
- Page 85 and 86: Federal Signal UltraVoice Installat
- Page 87 and 88: Federal Signal UltraVoice Installat
- Page 89 and 90: ACTIVE MODULE 1 2 3 4 5 6 DRIVER- T
Federal Signal <strong>UltraVoice</strong><br />
Installation and Operation <strong>Manual</strong><br />
Table 5 - Wiring example for four DSA3 speaker arrays<br />
Terminal Number Wire Color Drivers Array<br />
JP21-1 White/Brown A,B DSA3 #1&2<br />
JP21-2 Brown A,B DSA3 #1&2<br />
JP22-1 White/Brown A,B DSA3 #3&4<br />
JP22-2 Brown A,B DSA3 #3&4<br />
JP23-1 White/Red C DSA3 #1&2&3&4<br />
JP23-2 Red C DSA3 #1&2,&3&4<br />
Notes:<br />
1. The Brown wires from the first two DSA arrays must be tied together and connected<br />
to JP25-2. Likewise, the White/Brown wires from the first two DSA arrays must be<br />
tied together and connected to JP25-1. Repeat this procedure for the second two<br />
DSA arrays and connect to JP26.<br />
2.<br />
a. Connect the White/Red wire from DSA3 #1 to the Red wire from DSA3 #2.<br />
b. Connect the White/Red wire from DSA3 #3 to the Red wire from DSA3 #4.<br />
c. Connect the Red wires from DSA3 #1 and #3 together and jumper to JP23-2.<br />
d. Connect the White/Red wires from DSA3 #2 and #4 together and jumper to<br />
JP23-1.<br />
Note: See appendix A for drawing examples.<br />
INSTALLATION<br />
40