UltraVoice Manual - Alerting & Notification

More documents

Recommendations

Info

3. Drill a 3/8" pilot hole at each of the locations. Drill each hole at least 3-1/2" (90 mm.) deep. 4. Use a lift to lift the primary control battery box assembly to the desired height along the pole. Attach the primary control battery box assembly to the wall, using four (4) user-supplied 1/2" x 5" lag bolts. Slide a user-supplied 1/2" flat washer onto each bolt before threading the bolt into the pole. 5. Attach the primary control box assembly to the wall, using four (4) user-supplied 1/2" x 5" lag bolts. Slide a user-supplied 1/2" flat washer onto each bolt before threading the bolt into the pole. Repeat the process for the secondary cabinets (UV6048 models only). Federal Signal UltraVoice Installation and Operation Manual INSTALLATION 34
6. Install a user-supplied, fused, disconnect switch. Use the proper type required by the authority having jurisdiction in your area. 7. If the speaker array is installed on the roof of the building, it may be desirable to install the control and battery box inside the building, if practical. 5.1 Electrical Connections A. General Install the siren electrical system in compliance with local electrical codes and NEC recommendations. As a safety precaution to protect personnel and equipment, ALL SIREN UNITS MUST BE SOLIDLY CONNECTED TO AN EARTH GROUND. If the siren is installed on a building, ground the system to a metallic object known to be on a dedicated earth ground. For pole mounted installations, drive a metal rod or bar at least eight feet (8 ft.) into the ground, as close as practical to the base of the pole. FOR MAXIMUM PROTECTION, USE A SEPARATE, CONTINUOUS 6 AWG OR LARGER WIRE FROM THE SIREN FRAME TO GROUND AND FROM THE CABINET OF EACH SIREN UNIT TO GROUND. NOTE: CONDUIT CONNECTIONS MUST BE SEALED AND PROTECTED TO PREVENT WATER ENTRY AND CORROSION IN THE CONTROL CABINET. Federal Signal UltraVoice Installation and Operation Manual INSTALLATION 35 B. Power Connections 1. Route 1/2" conduit (steel preferred) between the usersupplied, fused disconnect switch and the conduit-fitting hole in the bottom right-hand of the control unit enclosure. Use weatherproof switches, electrical boxes and connectors to prevent water entry and corrosion. 2. Route two (2) user-supplied power wires and a ground wire through the conduit that was just installed between the control unit and the fuse disconnect box. Use wires no smaller than 14 AWG. Connect the ground wire to the green and yellow DIN mounted terminal block or the cabinet ground stud. Verify the appropriate siren model has been purchased. 240VAC models contain a step-down transformer pre-wired to the DIN rail located on the right side of the control cabinet. Connect the two AC power wires to the DIN mounted terminal blocks labeled L1 and L2. Connect the power wires and the lightning protector to the AC disconnect box per instructions provided with the lightning protector and governing electrical codes. C. Signal Connections Refer to the tables below for speaker wire connections. Module locations are 0 at the bottom, 1 next up etc.
Page 1 and 2: UltraVoice tm Electronic Siren Cont
Page 3 and 4: Federal Signal UltraVoice Installat
Page 7 and 8: SECTION IX - APPENDIX A Federal Sig
Page 9 and 10: Activation codes, command sequences
Page 11 and 12: Site Address Switch: Unit Address T
Page 13 and 14: Delay The delay function causes the
Page 15 and 16: 2.0 Electrical Federal Signal Ultra
Page 17 and 18: 2.4 Radio Communication Federal Sig
Page 21 and 22: Controls: Federal Signal UltraVoice
Page 23 and 24: 2.12 Audio Output to Amplifiers Fed
Page 27 and 28: functions programmed for that code,
Page 29 and 30: 4.0 Control Unit The information in
Page 33: 6. Drill a 3/8" pilot hole at each
Page 37 and 38: Table 2 - MOD6048 Speaker Wiring Fe
Page 39 and 40: Speaker Wiring for DSA Series Siren
Page 41 and 42: D. UVT6048 Inter-Cabinet Wiring 1.
Page 49 and 50: 5.4 Yagi Antenna Installation Yagi
Page 51 and 52: Note A: Objects around the antenna
Page 59 and 60: 7.0 General WARNING Service or main
Page 61 and 62: C. Battery Check 1. The voltage of
Page 63 and 64: 8. Turn service monitor to .25 V RF
Page 65 and 66: 7.4 Adjustment Procedure for a Two-
Page 69 and 70: 8.0 Radio Control The siren can be
Page 71 and 72: instructions in the programming sof
Page 73 and 74: Amplifier status for each amp in th
Page 75 and 76: Example DTMF Report String Federal
Page 79 and 80: 8.11 FS-SINAD Option Federal Signal
Page 81 and 82: Indicators Federal Signal UltraVoic
Page 83 and 84: 8.13 UV6048 Satellite Models Federa
Page 85 and 86:
Federal Signal UltraVoice Installat
Page 87 and 88:
Page 89 and 90:
ACTIVE MODULE 1 2 3 4 5 6 DRIVER- T
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111:
show all

UltraVoice Manual - Alerting & Notification

Create successful ePaper yourself

Delete template?

Save as template?