UltraVoice Manual - Alerting & Notification
UltraVoice Manual - Alerting & Notification UltraVoice Manual - Alerting & Notification
2.2 Battery Federal Signal UltraVoice Installation and Operation Manual Battery Voltage (72 F) 27.2 VDC nominal Recommended Batteries: Refer to Federal Signal web site for current recommended batteries. TABLE 2.1: Average Battery Temperature Values Battery Temperature Approximate Float Voltage 15 F / -9.4 C 29.40 20 F / -6.7 C 29.22 30 F / -1.1 C 28.84 40 F / 4.4 C 28.48 50 F / 10.0 C 28.12 60 F / 15.6 C 27.74 70 F / 21.1 C 27.38 80 F / 27.0 C 27.00 90 F / 32.2 C 26.64 NOTE: Batteries are to be user supplied. 2.3 Serial & I2C Ports Serial Ports Protocol RS232C 1200,N,8,1 I2C Port Protocol Philips Standard I 2 C SPECIFICATIONS 16
2.4 Radio Communication Federal Signal UltraVoice Installation and Operation Manual Receiver Module (UVL, UVH, UVU) Frequency Range 30 - 50, 151 - 168, 450 - 470 MHz SINAD Frequency Stability -30 C to 65 C + /- 5ppm for UHF, + /- 15ppm for High Band + /- 30ppm for Low Band Channel Spacing 30 kHz or 12.5 kHz LB and HB, 25 kHz or 12.5 kHz UHF Sensitivity Less than 0.35 uV for 12 dB Selectivity -70 dB at + /- 30 kHz Spurious Rejection -70 dB Image Rejection -70 dB Modulation Acceptance 7.5 kHz or 3.5 kHz (narrowband) Antenna Acceptance 50 ohms Decode Sensitivity 18 dB SINAD for Tone @ 3 kHz deviation (except w/ CTCSS tones >200 Hz & decode tones < 400 Hz) and 21 dB SINAD for MSK, EAS, POCSAG and DTMF with 50 ms/50ms or greater timing Squelch Sensitivity Minimum squelch setting = Open Squelch w/ 1 kHz tone @ 3 kHz deviation maximum squelch setting = < 30 dB SINAD SPECIFICATIONS 17
- Page 1 and 2: UltraVoice tm Electronic Siren Cont
- Page 3 and 4: Federal Signal UltraVoice Installat
- Page 5 and 6: Federal Signal UltraVoice Installat
- Page 7 and 8: SECTION IX - APPENDIX A Federal Sig
- Page 9 and 10: Activation codes, command sequences
- Page 11 and 12: Site Address Switch: Unit Address T
- Page 13 and 14: Delay The delay function causes the
- Page 15: 2.0 Electrical Federal Signal Ultra
- Page 19 and 20: Federal Signal UltraVoice Installat
- Page 21 and 22: Controls: Federal Signal UltraVoice
- Page 23 and 24: 2.12 Audio Output to Amplifiers Fed
- Page 25 and 26: Federal Signal UltraVoice Installat
- Page 27 and 28: functions programmed for that code,
- Page 29 and 30: 4.0 Control Unit The information in
- Page 31 and 32: Federal Signal UltraVoice Installat
- Page 33 and 34: 6. Drill a 3/8" pilot hole at each
- Page 35 and 36: 6. Install a user-supplied, fused,
- Page 37 and 38: Table 2 - MOD6048 Speaker Wiring Fe
- Page 39 and 40: Speaker Wiring for DSA Series Siren
- Page 41 and 42: D. UVT6048 Inter-Cabinet Wiring 1.
- Page 43 and 44: Federal Signal UltraVoice Installat
- Page 45 and 46: Federal Signal UltraVoice Installat
- Page 47 and 48: Federal Signal UltraVoice Installat
- Page 49 and 50: 5.4 Yagi Antenna Installation Yagi
- Page 51 and 52: Note A: Objects around the antenna
- Page 53 and 54: Federal Signal UltraVoice Installat
- Page 55 and 56: Federal Signal UltraVoice Installat
- Page 57 and 58: Federal Signal UltraVoice Installat
- Page 59 and 60: 7.0 General WARNING Service or main
- Page 61 and 62: C. Battery Check 1. The voltage of
- Page 63 and 64: 8. Turn service monitor to .25 V RF
- Page 65 and 66: 7.4 Adjustment Procedure for a Two-
2.4 Radio Communication<br />
Federal Signal <strong>UltraVoice</strong><br />
Installation and Operation <strong>Manual</strong><br />
Receiver Module (UVL, UVH, UVU)<br />
Frequency Range 30 - 50, 151 - 168, 450 - 470 MHz<br />
SINAD<br />
Frequency Stability -30 C to 65 C<br />
+ /- 5ppm for UHF,<br />
+ /- 15ppm for High Band<br />
+ /- 30ppm for Low Band<br />
Channel Spacing 30 kHz or 12.5 kHz LB and HB,<br />
25 kHz or 12.5 kHz UHF<br />
Sensitivity Less than 0.35 uV for 12 dB<br />
Selectivity -70 dB at + /- 30 kHz<br />
Spurious Rejection -70 dB<br />
Image Rejection -70 dB<br />
Modulation Acceptance 7.5 kHz or 3.5 kHz (narrowband)<br />
Antenna Acceptance 50 ohms<br />
Decode Sensitivity 18 dB SINAD for Tone @ 3 kHz deviation<br />
(except w/ CTCSS tones >200 Hz & decode<br />
tones < 400 Hz) and 21 dB SINAD for MSK,<br />
EAS, POCSAG and DTMF with 50 ms/50ms<br />
or greater timing<br />
Squelch Sensitivity Minimum squelch setting = Open Squelch<br />
w/ 1 kHz tone<br />
@ 3 kHz deviation maximum squelch setting<br />
= < 30 dB SINAD<br />
SPECIFICATIONS<br />
17
Change language