PG-C45X - diagramas.diagram...
PG-C45X - diagramas.diagram... PG-C45X - diagramas.diagram...
PG-C45X THE OPTICAL UNIT OUTLINE Layout for proper setup of the optical components and parts (top view) Relay lens 2 Relay lens3 Projection Lens M5 AL-coated mirror B L2 M4 AL-coated mirror R M3 B reflector Relay lens 1 L2 G reflector R reflector M2 16 L1 Fly-eye lens (Output) Fly-eye lens (Input) Light source (Lamp)
17 PG-C45X Adjusting the mirrors This adjustment is needed when any of the optical parts of the optical mechanism has been replaced. 1. Disconnect the flat cables from all the LCD panels. 2. Light up the lamp. 3. Project a white-light image and check to see if there is any color tint in any direction. If any, use the M2, M4 and M5 adjusting levers. 4. Loosen the adjusting lever lock screws, make adjustments, and tighten up the lock screws. Lock screws M5 Adjusting lever Lock screws M4 Adjusting lever M2 Adjusting lever Lock screws Lever D Screw A Screw B Correcting color irregularities on white-only screen when replacing the lamp If color irregularities are found at the right and left on a white-only screen after replacing the lamp, it is necessary to readjust the optical axis of the new lamp. Take the following steps. 1. Open the lamp cover and loosen the screws A and B at the top of the lamp. 2. Using a screwdriver or the like, move the lever D in the arrow direction. 3. Temporarily fix the screws A and B, close the lamp cover, and check the white-only screen again for color irregularities. 4. Repeat the above steps 1 and 2 until there will be no color irregularities. Now tighten up the screws A and B. 5. Finally secure the lamp cover back in position.
- Page 1 and 2: MODEL MODELL PG-C45X In the interes
- Page 3 and 4: IMPORTANT SERVICE SAFETY NOTES (for
- Page 5 and 6: 12345678901234567890123456789012123
- Page 7 and 8: Precautions for using lead-free sol
- Page 9 and 10: Projector (Rear View) USB Port AUDI
- Page 11 and 12: Connection Pin Assignments INPUT 1/
- Page 13 and 14: REMOVING OF MAJOR PARTS 13 PG-C45X
- Page 15: 1 2 Connect the power cord. • Plu
- Page 19 and 20: How to Release the System Lock 19 P
- Page 21 and 22: No. Adjustment Items Adjustment Con
- Page 23 and 24: No. Adjustment Items Adjustment Con
- Page 25 and 26: How to Adjust the PC I/F unit 25 PG
- Page 27 and 28: Group Sub Group Subject Process Mod
- Page 29 and 30: Lamp fails to light-up Turn on the
- Page 31 and 32: No audio output Is the audio signal
- Page 33 and 34: Checking the S-video system Is the
- Page 35 and 36: Checking the RGB Sync. Are the sync
- Page 37 and 38: 37 PG-C45X TROUBLE SHOOTING TABLE f
- Page 39 and 40: 39 PG-C45X TROUBLE SHOOTING TABLE f
- Page 41 and 42: 41 PG-C45X TROUBLE SHOOTING TABLE f
- Page 43 and 44: 4 43 PG-C45X TROUBLE SHOOTING TABLE
- Page 45 and 46: 5 45 PG-C45X TROUBLE SHOOTING TABLE
- Page 47 and 48: 47 PG-C45X TROUBLE SHOOTING TABLE f
- Page 49 and 50: HINWEIS FÜR DAS WARTUNGSPERSONAL 1
- Page 51 and 52: Bedienungsanleitung Projektor (Vord
- Page 53 and 54: Fernbedienung (Vordersicht) KEYSTON
- Page 55 and 56: Abmessungen Einheiten: Zoll (mm) 8
- Page 57 and 58: 57 PG-C45X 3. Entfernen der Leiterp
- Page 59 and 60: KURZBESCHREIBUNG DER OPTIK-EINHEIT
- Page 61 and 62: Ersetzen der Prismen-Einheit 1. Die
- Page 63 and 64: ELEKTRISCHE EINSTELLUNG Nr. Einstel
- Page 65 and 66: Nr. Einstellgegenstände Einstellbe
17<br />
<strong>PG</strong>-<strong>C45X</strong><br />
Adjusting the mirrors<br />
This adjustment is needed when any of the optical parts of the optical mechanism has been replaced.<br />
1. Disconnect the flat cables from all the LCD panels.<br />
2. Light up the lamp.<br />
3. Project a white-light image and check to see if there is any color tint in any direction. If any, use the M2, M4 and M5<br />
adjusting levers.<br />
4. Loosen the adjusting lever lock screws, make adjustments, and tighten up the lock screws.<br />
Lock screws<br />
M5 Adjusting lever<br />
Lock screws<br />
M4 Adjusting lever<br />
M2 Adjusting lever<br />
Lock screws<br />
Lever D<br />
Screw A<br />
Screw B<br />
Correcting color irregularities on white-only screen when replacing the lamp<br />
If color irregularities are found at the right and left on a white-only screen after replacing the lamp, it is necessary to<br />
readjust the optical axis of the new lamp. Take the following steps.<br />
1. Open the lamp cover and loosen the screws A and B at the top of the lamp.<br />
2. Using a screwdriver or the like, move the lever D in the arrow direction.<br />
3. Temporarily fix the screws A and B, close the lamp cover, and check the white-only screen again for color<br />
irregularities.<br />
4. Repeat the above steps 1 and 2 until there will be no color irregularities. Now tighten up the screws A and B.<br />
5. Finally secure the lamp cover back in position.