Eco Compact H1 Series - Ferret

Specifications
Model PDAP22FSN2 PDAP28FSN2 PDAP45FSN2 PDAP56FSN2 PDAP71FSN2 PDAP90FSN2 PDAP112FSN2 PDAP140FSN2
(P22)
(P28)
(P45)
(P56)
(P71)
(P90)
(P112)
(P140)
Cooling (kW) 2.2
2.8
4.5
5.6
7.1
9.0
11.2
14.0
Capacity Heating (kW) 2.5
3.2
5.0
6.3
8.0
10.0
12.5
16.0
Low temp.
heating (kW) 2.8
3.4
5.3
6.7
8.5
10.6
13.2
17.0
Dimensions Height (mm) 270
270
270
270
350
350
350
350
Unit (Standard
panel)
Width
Depth
(mm)
(mm)
650 + 75
720
650 + 75
720
650 + 75
720
900 + 75
720
900 + 75
720
900 + 75
800
900 + 75
800
1300 + 75
800
(kg) 26
26
26
35
35
46
46
58
Power supply
0.11
0.11
0.15
0.15
0.15
0.31
0.31
0.46
0.11
0.11
0.15
0.15
0.15
0.31
0.31
0.46
0.51
0.51
0.69
0.69
0.69
1.44
1.44
2.13
0.51
0.51
0.69
0.69
0.69
1.44
1.44
2.13
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
90
Air filter
Type
Motor output (kW) 0.06
0.06
0.06
0.075
0.075
0.15
0.29
0.29
H (m 8
8
13
15
16
25
27
37
Air flow
amount
M
7
7
11
13
14
21
23
31
L
6
6
9
11
12
17
19
25
External static pressure
50 (L: 30 H: 80)
120 (L: 60 H: 170)
Sound pressure
level
H
M
36
34
36
34
36
34
36
34
37
35
43
40
45
42
46
43
L
32
32
32
32
33
36
38
39
Refrigerant
(Flare
connections)
Liquid
Gas
6.4
12.7
6.4
12.7
6.4
12.7
6.4
12.7
9.5
15.9
9.5
15.9
9.5
15.9
9.5
15.9
Drain piping
Colour Munsell number
Remote controller Model name
3 /min.)
(m3 /min.)
(m3 Weight Unit (Panel)
Single phase, 240 V, 50 Hz
Power Cooling (kW)
consumption
Heating (kW)
Running Cooling (A)
current
Heating (A)
Power Cooling (%)
factor
Heating (%)
Polypropylene, mould proof
Sirocco fan
/min.)
(Pa)
(dB (A))
(dB (A))
(dB (A))
(mm)
(mm)
VP25, external
Galvanised steel sheet
PLPAR
(1) The rated capacity is the system performance by a standard indoor/outdoor unit combination with a 7.5 m piping length and 0 m level difference.
Cooling capacity: 27 CDB/19 CWB indoor suction air temp., 35 CDB outdoor suction air temp. Heating capacity: 20 CDB indoor suction air temp., 7 CDB/6 CWB outdoor
suction air temp. Low-temp. heating capacity: 20 CDB indoor suction air temp., 2 CDB/1 CWB outdoor suction air temp.
(2) The sound pressure level is the value measured at a height of 1.5 m, 1 m from the front of the unit and calculated with zero echo considered. When the unit is actually installed,
the sound pressure level will be affected by ambient noise and echoes and will normally be more than the values specified above.
(3) The values above are for a single indoor unit.
(4) Capacity characteristics vary according to the combination of indoor and outdoor units.
(5) Specifications are subject to change without notice due to product improvements.
Electrical characteristics 50 Hz
Fan
Piping
connection
Dimensions (Unit: mm)
30
P22 to P140
20
22
N
M
30
20 22
220
P
40
48.5
E
E
300
B
A
C x300=
D
(Circumference of flange)
4-40 x 12 long hole
(for suspension)
Twist pair cable (0.75 mm2 L -ø6
or more)
(must be obtained locally)
Remote controller
120
300
L -ø6
C x 300=
D
A
Air outlet (front side)
(Circumference of flange)
Refrigerant gas pipe connection port
75 (Electric box) (ø I copper tube with flare nut)
Drain pipe connection port
Refrigerant liquid pipe connection port (VP25)
(ø H copper tube with flare nut)
U 45
F
97
Q
T 2x90=180
90
S
R
23
J (Refrigerant gas pipe connection position)
90 (Drain pipe connection position)
K (Refrigerant liquid pipe connection position)
Operation circuit
connection port
Power supply
connection port
600
1000
1000
V
35
2x V = W
246 (Refrigerant liquid pipe connection position)
321 (Refrigerant gas pipe connection position)
377 (Drain pipe connection position)
Top side
Electric box
(Rear side)
Inspection port (For the M dimensions, install the drain pipe
at a height that ensures sufficient slope.)
( 450 or more)
(Front (130)
Create a section that will function as an
side)
opening for the lower surface of the indoor
unit. This opening should be made in a
location where the ceiling panel will not easily
detach but where the indoor unit itself can be
600 or more
removed.
Top side Service space
Y
Air inlet
G
X
22
33.5
Notes
1. Take steps to prevent vibrations by using a canvas joint for the duct
section and an anti-vibration hanger for the unit body. This will
prevent vibrations from the unit body being transferred to the ceiling
or mounting block.
2. If the external static pressure is set too high for the ducts, the air
speed will increase significantly, causing a large amount of noise
and spraying of water. In this case, install a damper to regulate the
air volume or change the static pressure adjustment so that the
external static pressure is equal to the pressure loss for the ducts.
3. Use the companion flanges included with the product as the duct
connection companion flanges for both the air intake and discharge
sides.