Astro - Ems-access.co.uk

Recommendations

Info

3.3.1.2 Power Supplies Power usage is given in the datasheet, chapter 4.1. Make sure that the supply and battery backup is sufficient is for the required power and backup time. Take into account the use of door strikes as well. 3.3.1.3 Orbit outputs The Orbit has various solid-state relays that can be used to switch a door strike (or other equipment). 3.3.1.4 Inputs These relays are only suitable for D.C. and maximum 28 Volt at 1 Ampere (not inductive). One side of the relays is grounded: each relay switches one contact to ground (see drawing 76000160): all outputs, OUT0 and OUT1 of each reader, have a common, ground. These relays are not suitable for all possible situations. If, for example, an electrically isolated switch is required, an additional mechanical relay is needed. Note This outputs are normally open (N.O.) when the power is removed from Astro. For high security situations where N.C. contacts are used, it is necessary to use an additional mechanical relay. Inputs (for door contacts, loops, etc.) are shown in the drawing 76000160. • One side of all inputs is grounded. • The other side of the input must be shorted to ground in order to activate the input. Normal switches can be used with these inputs without any problems. Note Before connecting other equipment to Astro, consult the specifications of the equipment to prevent conflicts and possible damage. 3.3.1.5 PC Hardware and Software Astro is designed to function with Microsoft Internet Explorer, version 6.0 or later. If an earlier version is used, some screens may not function properly. The Internet Explorer on the Astro CD is suitable for Astro. 3.3.2 Mechanical Installation There are no specific requirements for the PC as the browser application is quite simple. No additional software need be installed on the PC. 3.3.2.1 Readers and Locks Determine where the readers are to be mounted and obtain the necessary mounting materials. Page ● 3-4 IE Keyprocessor
3.3.2.2 Astro Note 3.4 Installation 3.4.1 Cabling 3.4.2 Housing Note The proximity readers are mounted with screws from the front side of the reader, while the SL4 reader can only be mounted with bolts from the rear of the reader. Mounting information is included with each of the readers. Mounting materials are provided only for the SL4 reader. In certain situations this material may not be suitable. Ascertain that you have sufficient and suitable materials for the readers you must install. Mount the door strikes when installing the readers. The distance between two Proximity readers (PX007B/MF) must be at least 20 centimeters. See also the mounting instructions on page 4-14. The Astro is normally mounted in the cabinet on the DIN-rail. Mounting materials are only necessary in order to mount the cabinet. Take into account the following: • Distance Astro – Readers. • Mounting supply and battery backup. • Network cable length to HUB / PC. The following tasks can be done in any desired order. ► Lay all the cables in secure areas. ► Take care that all cables are sufficiently protected from wear and tear as well as from external electrical disturbances. In the instruction below, we assume Astro is mounted in the IEcabinet. ► Mount the cabinet. A mechanical drawing of the cabinet is included. ► Mount the Astro on the Din-rail. ► Mount the Supply. ► Connect the supply to Astro. Do not turn on the power for the Astro. If the supply fails for a long period, the date and time will not be preserved. This can result in incorrect access control functions. This can be avoided by using a battery backup. IE Keyprocessor Page ● 3-5
Page 1 and 2: Stap-voor-stap-handleiding Step by
Page 3 and 4: Inhoudsopgave / Contents 2 Nederlan
Page 5 and 6: 1 Introductie / Introduction 1.1 Ne
Page 7 and 8: • CD met Acrobat reader and Inter
Page 9 and 10: 2.3.1.3 Uitgangen 2.3.1.4 Ingangen
Page 11 and 12: 2.4.3 Lezers eropgezet wordt). Dit
Page 13 and 14: 2.5.1.2 Taal instellen ► Login He
Page 15 and 16: ► Vul het gewenste IP adres in bi
Page 17 and 18: Met de dialoog zoals hieronder, zet
Page 19 and 20: ► Zet het vinkje bij Geldig aan,
Page 21 and 22: 2.5.3.5 Aansluitingen testen Met de
Page 23 and 24: 2.6.1.3 PX007A 2.6.1.4 MF PIC 2.6.1
Page 25: 500-8020 SmartID/MF/SNR 500-8030 Sm
Page 28 and 29: 3.1.2 Standard and Optional Compone
Page 32 and 33: 3.4.3 Readers 3.5 ► Connect the r
Page 34 and 35: 3.5.1.2 Set the Language ► Login
Page 36 and 37: ► Enter the desired IP address
Page 38 and 39: Using this dialog, set time zone 1
Page 40 and 41: ► Set the checkbox by Valid and c
Page 42 and 43: 3.5.3.5 Hardware test After complet
Page 44 and 45: 3.6.1.2 PX007B 3.6.1.3 PX007A 3.6.1
Page 46 and 47: Services IE Keyprocessor 901-0160 T
Page 48 and 49: 4.1 Datasheet Technical specificati
Page 50 and 51: 4.2 Connection PX007 or SmartID: As
Page 52 and 53: 4.4 Connection PX007Z/MF(SNR) : Ast
Page 54 and 55: 4.6 Connections PX106 : 76000172 Pa
Page 56 and 57: 4.8 Connections 5311 and HF103/LTU
Page 58 and 59: 4.10 76000167 Page ● 4-12 IE Keyp
Page 60 and 61: 4.12 Mounting instructions PX007 (7
Page 62: Page ● 4-16 IE Keyprocessor

Astro - Ems-access.co.uk

Create successful ePaper yourself

Delete template?

Save as template?