Residual Strength and Fatigue Lifetime of ... - Solid Mechanics
Residual Strength and Fatigue Lifetime of ... - Solid Mechanics Residual Strength and Fatigue Lifetime of ... - Solid Mechanics
This page is intentionally left blank. 144
Appendix A Additional Results from the Column Compression Tests In this appendix additional results from the compression tests performed on debonded columns studied in Chapter 2 are presented. A.1 Debonded Columns with H45 Core In this section the axial displacement vs. load and load vs. out-of-plane displacement curves of the columns with H45 core are presented. The out-of-plane deflection refers to the centre of the debond. Load (kN) 16 12 8 4 0 12 8 (a) (b) (c) Column 1 Column 2 Column 3 0 0.5 1 1.5 2 Axial Displacement (mm) Load (kN) 8 4 0 0 0.5 1 1.5 2 Axial Displacement (mm) Figure A.1: Axial displacement vs. load for the H45 columns with a debond length of (a) 25.4 mm, (b) 38.1 mm and (c) 50.8 mm. 145 Column 1 Column 2 Column 3 Load (kN) 6 4 2 0 Column 1 Column 2 0 0.2 0.4 0.6 Axial Displacement (mm)
- Page 116 and 117: Figure 5.5: Test setup. Initially,
- Page 118 and 119: H100 Specimen Fibre bridging Figure
- Page 120 and 121: propagation, the crack continues to
- Page 122 and 123: Figure 5.14: Kinking of the crack i
- Page 124 and 125: Crack length [mm] Crack length [mm]
- Page 126 and 127: mode-mixity phase angle was chosen
- Page 128 and 129: should be taken into account for a
- Page 130 and 131: Figure 5.25: Kinking of the crack i
- Page 132 and 133: log (da/dN) (mm/cycle) 10 log G (J/
- Page 134 and 135: erroneous extrapolations in the tra
- Page 136 and 137: compared to the 65% efficiency obta
- Page 138 and 139: the case of uneven debond growth, t
- Page 140 and 141: Load (kN) 2 1.5 1 0.5 0 Panel 1 Pan
- Page 142 and 143: Figure 5.42: Zero and ninety degree
- Page 144 and 145: G(J/m 2 ) 180 150 210 120 150 100 5
- Page 146 and 147: 110 q=qG=0.4 Test #1 100 Test #2 Te
- Page 148 and 149: panels were determined for differen
- Page 150 and 151: Chapter 6 Conclusion and Future Wor
- Page 152 and 153: toughness using MMB fracture toughn
- Page 154 and 155: For the specimens with H250 core th
- Page 156 and 157: Development of testing methods for
- Page 158 and 159: This page is intentionally left bla
- Page 160 and 161: Bezazi A., Mahi A. E., Berthelot J.
- Page 162 and 163: Kanny K. and Mahfuz H. (2005), Flex
- Page 164 and 165: Ratcliffe J. and Cantwell W. J. (20
- Page 168 and 169: Out-of-plane displacement (mm) 1 0.
- Page 170 and 171: Out-of-plane displacement (mm) 3 2
- Page 172 and 173: A.5 Out-of-plane deflection of Debo
- Page 174 and 175: (a) Figure A.14: Out-of-plane defle
- Page 176 and 177: (a) (b) Figure A.18: Out-of-plane d
- Page 178 and 179: Load (kN) 250 200 150 100 50 250 30
- Page 180 and 181: Displacement (mm) 4 3 2 1 0 8 9 (a)
- Page 182 and 183: (a) (b) Figure B.11: Out-of-plane d
- Page 184 and 185: (a) (b) Figure B.15: Out-of-plane d
- Page 188: DTU Mechanical Engineering Section
This page is intentionally left blank.<br />
144