Residual Strength and Fatigue Lifetime of ... - Solid Mechanics
Residual Strength and Fatigue Lifetime of ... - Solid Mechanics Residual Strength and Fatigue Lifetime of ... - Solid Mechanics
This page is intentionally left blank. 136
References Avery J. L., and Sankar B. V. (2000), Compressive Failure of Sandwich Beams with Debonded Face Sheets, Journal of Composite Materials, 34: 1176-1199. Avilés F. and Carlsson L. A. (2007), Post-Buckling and Debond Propagation in Panels Subjected to In-Plane Loading, Engineering Fracture Mechanics, 74: 794-806. Avilés F. and Carlsson L. A. (2008), Analysis of the Sandwich DCB Specimens for Debond Characterization, Engineering Fracture Mechanics, 75:153–68. Aviles, F. and Carlsson, L. A. (2006), Experimental Study of Debonded Sandwich Panels under Compressive Loading, Journal of Sandwich Structures & Materials, 8(1): 7-31. Berggreen C. and Carlsson L. A. (2010), A Modified TSD Specimen for Fracture Toughness Characterization - Fracture Mechanics Analysis and Design, Journal of Composite Materials, 44(15): 1893-1912. Berggreen C. and Simonsen B. (2005), Non-Uniform Compressive Strength of Debonded Sandwich Panels - II. Fracture Mechanics Investigation, Journal of Sandwich Structures and Materials, 7(6): 483-517. Berggreen C., Simonsen B. and Borum K. (2007), Experimental and Numerical Study of Interface Crack Propagation in Foam-Cored Sandwich Beams, Journal of Composite Materials, 41: 493-520. Berkowitz K. C. and Johnson W. (2005), Fracture and Fatigue Tests and Analysis of Composite Sandwich Structure, Journal of Composite Materials, 39(16): 1417-1431. Beuth J. L. (1996), Separation of Crack Extension Modes in Orthotropic Delamination Models, International Journal of Fracture, 77: 305-321. Bezazi A., Mahi A. E., Berthelot J. M. and Bezzazi B. (2007), Experimental Analysis of Behavior and Damage of Sandwich Composite Materials in Three-Point Bending Part 1: Static Tests and Stiffness Degradation at Failure Studies, Strength of Materials, 39(2): 170-177. 137
- Page 108 and 109: using the cycle jump method, more t
- Page 110 and 111: Chapter 5 Face/Core Interface Fatig
- Page 112 and 113: of this chapter, sandwich panels wi
- Page 114 and 115: H250 Specimen H100 Specimen H45 Spe
- Page 116 and 117: Figure 5.5: Test setup. Initially,
- Page 118 and 119: H100 Specimen Fibre bridging Figure
- Page 120 and 121: propagation, the crack continues to
- Page 122 and 123: Figure 5.14: Kinking of the crack i
- Page 124 and 125: Crack length [mm] Crack length [mm]
- Page 126 and 127: mode-mixity phase angle was chosen
- Page 128 and 129: should be taken into account for a
- Page 130 and 131: Figure 5.25: Kinking of the crack i
- Page 132 and 133: log (da/dN) (mm/cycle) 10 log G (J/
- Page 134 and 135: erroneous extrapolations in the tra
- Page 136 and 137: compared to the 65% efficiency obta
- Page 138 and 139: the case of uneven debond growth, t
- Page 140 and 141: Load (kN) 2 1.5 1 0.5 0 Panel 1 Pan
- Page 142 and 143: Figure 5.42: Zero and ninety degree
- Page 144 and 145: G(J/m 2 ) 180 150 210 120 150 100 5
- Page 146 and 147: 110 q=qG=0.4 Test #1 100 Test #2 Te
- Page 148 and 149: panels were determined for differen
- Page 150 and 151: Chapter 6 Conclusion and Future Wor
- Page 152 and 153: toughness using MMB fracture toughn
- Page 154 and 155: For the specimens with H250 core th
- Page 156 and 157: Development of testing methods for
- Page 160 and 161: Bezazi A., Mahi A. E., Berthelot J.
- Page 162 and 163: Kanny K. and Mahfuz H. (2005), Flex
- Page 164 and 165: Ratcliffe J. and Cantwell W. J. (20
- Page 166 and 167: This page is intentionally left bla
- Page 168 and 169: Out-of-plane displacement (mm) 1 0.
- Page 170 and 171: Out-of-plane displacement (mm) 3 2
- Page 172 and 173: A.5 Out-of-plane deflection of Debo
- Page 174 and 175: (a) Figure A.14: Out-of-plane defle
- Page 176 and 177: (a) (b) Figure A.18: Out-of-plane d
- Page 178 and 179: Load (kN) 250 200 150 100 50 250 30
- Page 180 and 181: Displacement (mm) 4 3 2 1 0 8 9 (a)
- Page 182 and 183: (a) (b) Figure B.11: Out-of-plane d
- Page 184 and 185: (a) (b) Figure B.15: Out-of-plane d
- Page 188: DTU Mechanical Engineering Section
This page is intentionally left blank.<br />
136
Change language