Evaluation of Plastic Waste Management in Thailand Using Material ...

More documents

Recommendations

Info

Table E-8 Details of each flow of scenario 2B (continued) No. Description Value (Tonnes/year) Assumption and Calculation 19 Plastic waste (Thermoplastic) in MSW 2,608,181 Plastic waste (Thermoplastic) = Total Plastic Waste - Plastic waste (Thermosetting) (Not present in the material flow) 20 Uncollected waste (Thermosetting) in MSW 2,635 Assumed that 10% of thermosetting waste generation in MSW will not be collected to dispose in 2016. (Not present in the material flow) 21 Uncollected waste (Thermoplastic) in MSW 260,818 Assumed that 10% of thermoplastic waste generation in MSW will not be collected to dispose in 2016. (Not present in the material flow) 22 Uncollected waste 263,453 The summary of uncollected thermosetting and thermoplastic wastes 23 Calculated stock by STAN 1,849,040 Stock = input of process - output of process 24 Collected plastic waste (Thermosetting) in MSW 23,711 Plastic waste collected = Plastic waste (Thermosetting) - Uncollected waste (Thermosetting) 25 Collected plastic waste (Thermoplastic) in MSW 2,347,363 Plastic waste collected = Plastic waste (Thermoplastic) - Uncollected waste (Thermoplastic) 26 Industrial plastic waste generation in other industries 1,061,967 Assumed that 50% of industrial plastic waste generation is generated in the plastic consumption process (Not present in the material flow) 27 28 29 30 Industrial plastic waste for recycling (2) Reuse (stocked) industrial plastic waste (2) Landfilling of industrial plastic waste (2) Industrial plastic waste for industrial incineration (2) 318,590 106,197 10,620 626,560.68 31 Industrial plastic waste (2) 955,771 The percentage of recycling rate of industrial plastic waste will increase by 30% within 2016. (Not present in the material flow) Assumed that 10% of industrial plastic wastes will be reused or stocked in the manufacturing in 2016. (Not present in the material flow) Assumed that 1% of industrial plastic wastes will be disposed at landfills in 2016. (Not present in the material flow) Assumed that 59% of industrial plastic waste (use as fuels) will be burnt in industrial incineration to recovery energy. (Not present in the material flow) The amount of industrial plastic wastes was shown in the material flow of scenario 2. IPW (2) = IPW (recycling)+IPW (landfilling)+IPW (incineration) 223
Table E-8 Details of each flow of scenario 2B (continued) No. Description Value (Tonnes/year) Collection and transportation process 32 Exported plastic waste 352,104 33 34 Municipal incineration (Thermosetting) Municipal incineration (Thermoplastic) 474 46,947 224 Assumption and Calculation Assumed that 15% of collected plastic waste (Thermoplastic) will be exported in 2016. (this amount includes only thermoplastic waste not including Thermosetting) Assumed that 2% of municipal solid wastes will be burnt at the incinerators (Not present in the material flow) 2% of municipal solid wastes will be burnt at the incinerators (Not present in the material flow) 35 Municipal incineration 47,421 The summary of wastes to municipal incineration from each source 36 37 38 39 Industrial incineration (Thermosetting) of MPW Industrial incineration (Thermoplastic) of MPW Industrial incineration (Municipal plastic waste) Industrial incineration (industrial plastic waste) 1,186 117,368 118,554 1,253,121.36 40 Reuse (Thermosetting) 1,186 Assumed that 5% of thermosetting waste in MSW will be produced as RDF for using in the industrial incineration Assumed that 5% of thermoplastic waste in MSW will be produced as RDF for using in the industrial incineration The summary of municipal wastes to industrial incineration (RDF) from each source (Not present in the material flow) IPW for incineration = IPW 1 (incineration) + IPW 2 (incineration) = 626,560.68+ 626,560.68 Assumed that 5% of thermosetting waste will be reused as secondary products for using in the consumption process in 2016. (Not present in the material flow) 41 Reuse (Thermoplastic) 117,368 Assumed that 5% of thermoplastic waste will reused as secondary products for using in the consumption process in 2016. (Not present in the material flow) 42 Reuse of MPW 118,554 The summary of reused municipal wastes to plastic consumption process. 43 Landfilling (Thermosetting) 9,484 Assumed that 40% of municipal thermosetting wastes will be disposed at landfills in 2016. (Not present in the material flow)
Page 1 and 2:
Evaluation of Plastic Waste Managem
Page 3 and 4:
Abstract Rapid increase in the usag
Page 5 and 6:
List of Tables Table Title Page 2.1
Page 7 and 8:
4.7 Percentage of municipal solid w
Page 9 and 10:
PETE Polyethylene Terephthalate PIT
Page 11 and 12:
Plastic wastes are mostly recycled
Page 13 and 14:
4R principle includes recovery, rec
Page 15 and 16:
Table 2.2 Codes, characteristics of
Page 17 and 18:
2. Injection molding: First, the pl
Page 19 and 20:
Vacuum forming: A vacuum is formed
Page 21 and 22:
2.2.3 Uses of plastic Figure 2.11 C
Page 23 and 24:
5. Housewares: This kind of product
Page 25 and 26:
process usually involves two steps,
Page 27 and 28:
Refuse Derived Fuel in Thailand The
Page 29 and 30:
product from gas into liquid. The p
Page 31 and 32:
Figure 2.24 Coke oven chemical feed
Page 33 and 34:
2.3.3.2 Re-melted to make products
Page 35 and 36:
3. Chapter 7 on penalties It should
Page 37 and 38:
Adjust system Problem Definition Sy
Page 39 and 40:
There are 0.25 million workers in r
Page 41 and 42:
2. Collecting and recording the inf
Page 43 and 44:
For example, if the stakeholder has
Page 45 and 46:
(DENR). A pilot collection program
Page 47 and 48:
3.2 Study Area Seven provinces name
Page 49 and 50:
3.3 Sample Size The sample groups w
Page 51 and 52:
Figure 3.4 Initial flow of plastic
Page 53 and 54:
Table 3.1 Details of Needed Informa
Page 55 and 56:
questionnaires, interview, field ob
Page 57 and 58:
From Table 3.2, the stakeholders we
Page 59 and 60:
Institute Foundation (FPRI) made a
Page 61 and 62:
12%, 10%, and 7% respectively. The
Page 63 and 64:
From Figure 4.5, this figure shows
Page 65 and 66:
Plastic 17% Paper 8% Metal 2% Glass
Page 67 and 68:
Figure 4.9 BMA waste collectors Fig
Page 69 and 70:
Similarly, some recycling factories
Page 71 and 72:
Figure 4.21 Material flow of plasti
Page 73 and 74:
50% of agricultural products was co
Page 75 and 76:
Figure 4.25 Recycling and plastic t
Page 77 and 78:
From Figure 4.26, the material flow
Page 79 and 80:
future is the same as current situa
Page 81 and 82:
From Figure 4.28, total plastic pel
Page 83 and 84:
The one issue of plastic waste segr
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Most municipal plastic wastes (37%)
Page 91 and 92:
From Figure 4.33, the revenue from
Page 93 and 94:
sectors by the government organizat
Page 95 and 96:
industrial waste incineration of ea
Page 97 and 98:
4.4.1. Lists of stakeholders and th
Page 99 and 100:
of them. For example, one individua
Page 101 and 102:
Local administrative bodies are als
Page 103 and 104:
was presented, and the percentage o
Page 105 and 106:
5.1 Conclusions Chapter 5 Conclusio
Page 107 and 108:
11. A simple revenue-expenditure an
Page 109 and 110:
References BBC News. (2008). Plasti
Page 111 and 112:
Jinran, Z. (2011). Ban on free plas
Page 113 and 114:
Plastic Waste Management Institute.
Page 115 and 116:
Treewijitkasam, P. (2013). Understa
Page 117 and 118:
Table A-1 Details of parameters and
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
A-2: Harmonized System Code Table A
Page 127 and 128:
Table A-11 Characteristics of stake
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
- What is the knowledge that the wa
Page 137 and 138:
2.5 Who do you buy plastic wastes f
Page 139 and 140:
4. Environmental, law, policy, and
Page 141 and 142:
B.3 Questionnaire for Household Dat
Page 143 and 144:
B.4 Questionnaire for Plastic Recyc
Page 145 and 146:
3. Production process information a
Page 147 and 148:
B.5 Questionnaire for Waste picker/
Page 149 and 150:
B.6 Checklists for waste collector
Page 151 and 152:
2.8 Which kinds of plastic products
Page 153 and 154:
This shop does not buy foam, plasti
Page 155 and 156:
(a) Non-stored bottles 146 (b) Undi
Page 157 and 158:
c) Plastic pellet sack Figure C-6 S
Page 159 and 160:
matters/dust. This shop is a stable
Page 161 and 162:
Washing and drying process are oper
Page 163 and 164:
C.2 Case study from oil recovery pl
Page 165 and 166:
silicate clay, natural clay, metal-
Page 167 and 168:
Residue wastes are produced about 1
Page 169 and 170:
C.3 Case study from zero baht shop
Page 171 and 172:
Figure C-24 Newspaper Figure C-26 M
Page 173 and 174:
3. Activities of Zero Baht Shop On
Page 175 and 176:
Zero Baht Shop depending on the tot
Page 177 and 178:
Figure C-37 Lecturer of the project
Page 179 and 180:
networks. This project is not widel
Page 181 and 182: C.4 Case study from Sai Mai transfe
Page 183 and 184: 4. Categorizing of waste Waste from
Page 185 and 186: 6. Environment issues and observati
Page 187 and 188: C.5 Technology Park of Chulalongkor
Page 189 and 190: fractions. It utilizes the heat fro
Page 191 and 192: ates and desorption inside capillar
Page 193 and 194: Appendix D Material Flow Analysis D
Page 195 and 196: Table D-1 Amounts of plastic waste
Page 197 and 198: D.2 Calculation of the material flo
Page 199 and 200: Table D-2 Details of calculation of
Page 215 and 216: Table D-3 Percentage of industrial
Page 217 and 218: E.3 Calculation of plastic flows in
Page 219 and 220: Table E-3 Details of each flow of s
Page 223 and 224: E.4 The estimation of imported and
Page 231: Table E-8 Details of each flow of s
show all

Evaluation of Plastic Waste Management in Thailand Using Material ...

Create successful ePaper yourself

Delete template?

Save as template?