Ethernet Configuration and Control, cont'd - Extron Electronics

More documents

Recommendations

Info

PRELIMINARY SIS Programming and Control, cont’d Command/response table for SIS commands (continued) 5-16 Command ASCII (Telnet) URL Encoded (Web) Response Reset (zap) and erase commands None of the following ZAP commands (ZFFF, ZXXX, ZY, and ZQQQ) reset the AC power receptacle. Power remains in its current state. Erase all files from flash memory24 Esc ZFFF WZFFF| Zpf Reset all device settings to factory default24 Esc ZXXX WZXXX| Zpx This reset is product-dependent. It resets receptacle name and executive mode to Off. It does not reset IP settings such as IP address, subnet mask, gateway IP address, and IP Security level table; and it does not remove the user file system. Absolute system reset; retain IP address Esc ZY WZY| Zpy This reset is the same as ZQQQ except that it excludes IP settings such as IP address, subnet mask, gateway IP address, unit name, DGCP, and port mapping (Telnet/Web/ Direct Access) in order to preserve communication with the device. It also erases the user file system. This reset is recommended after a firmware update. Absolute system reset24 Esc ZQQQ WZQQQ| Zpq This is a mode 5 reset. It resets all device settings to the factory defaults; however, the firmware version remains the same. IPL T PC1 SIS Programming and Control
IPL T PC1 Appendix A Reference Material Specifications Part Numbers and Accessories Glossary
Page 1 and 2:
IP Link Power Control Interface IPL
Page 3 and 4:
FCC Class A Notice This equipment h
Page 5 and 6:
Table of Contents Chapter 1 Introdu
Page 7 and 8:
Using the Command/Response Table ..
Page 9 and 10:
IPL T PC1 1 Chapter One Introductio
Page 11 and 12:
Web-based A/V asset management —
Page 13 and 14:
IPL T PC1 2 Chapter Two Installatio
Page 15 and 16:
Reduced air flow — Installation o
Page 17 and 18:
3 COM port (RS-232) — Connect the
Page 19 and 20:
Side View Pins: 12345678 Insert Twi
Page 21 and 22:
IPL T PC1 3 Chapter Three Front Pan
Page 23 and 24: Setting Up the System Using the Fro
Page 25 and 26: Result — The RS-232 port is conve
Page 27 and 28: IPL T PC1 4 Chapter Four Ethernet C
Page 29 and 30: ARP-S command screen 6. Execute a p
Page 31 and 32: 2. Right-click Local Area Connectio
Page 33 and 34: 7. Set up the PC1’s IP address. S
Page 35 and 36: Passwords must contain 4 to 12 alph
Page 37 and 38: 2. Enter your new information in th
Page 39 and 40: RS-232 port From the drop-boxes in
Page 41 and 42: 3. In the Re-enter Admin Password f
Page 43 and 44: 4. Click Save to save the informati
Page 45 and 46: 2. Click Browse to open a Choose fi
Page 47 and 48: “Set Schedule For” field, displ
Page 49 and 50: 2. In either the Power ON or Power
Page 51 and 52: Adding a directory To add a directo
Page 53 and 54: The figure below shows the HTML cod
Page 55 and 56: Accessing and Using Telnet (Port 23
Page 57 and 58: Network connections 1. Check the ne
Page 59 and 60: IPL T PC1 5 Chapter Five SIS Progr
Page 61 and 62: The error response codes and their
Page 63 and 64: Symbol definitions = CR/LF (carriag
Page 65 and 66: X712 = Time in minutes (0-1440) 0 =
Page 67 and 68: Command/response table for SIS comm
Page 73: Command/response table for SIS comm
Page 77 and 78: General Power input ...............
Page 79 and 80: Glossary 10/100Base-T is Ethernet t
Page 81 and 82: IP address is a unique, 32-bit, bin
Page 83 and 84: Extron’s Warranty Extron Electron
show all

Ethernet Configuration and Control, cont'd - Extron Electronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?