Ethernet Configuration and Control, cont'd - Extron Electronics

More documents

Recommendations

Info

PRELIMINARY SIS Programming and Control, cont’d Command/response table for SIS commands (continued) 5-12 Command ASCII (Telnet) URL Encoded (Web) Response IP Setup, continued View verbose mode status Esc CV WCV| X22 Set broadcast mode Esc X64 , X14 EB W X64 %2C X14 EB| Bmd X64 , X14 Set broadcast mode to default address Esc X64 EB W X64 EB| Bmd X64 , X14 Clear broadcast mode Esc 0EB W0EB| Bmd 000, X14 View broadcast mode Esc EB WEB| X64 , X14 Set broadcast port and MAC address Esc port# * X71 * X72 PB W port# * X71 * X72 PB| Bpt port# * X18 View broadcast port and MAC address Esc PB WPB| port# * X18 port# is the UDP outgoing port. X71 * X72 is the MAC address for UDP unicast transmissions. Get connection listing Esc CC WCC| Number of connections With tagged response – verbose modes 2 and 3: Icc number of connections IPL T PC1 SIS Programming and Control Password and security settings Set administrator password24 Esc X33 CA W X33 CA| Ipa X41 Clear administrator password24 Esc CA W%20CA| Ipa Entering a password when the IPL T PC1 has not been configured for one yields an E14 response from the interface. A user password cannot be assigned if an administrator password does not exist. If the administrator password is cleared (removed), the user password is also removed. View administrator password24 Esc CA WCA| X41 Set user password14 24 Esc X33 CU W X33 CU| Ipu X41 Clear user password24 Esc CU W%20CU| Ipu View user password24 Esc CU WCU| X41 Query session’s security level Esc CK WCK| X52 With tagged response – verbose modes 2 and 3: Pvl X52 The Password: prompt requires a password (administrator level or user level), followed by a carriage return. The password prompt appears only if there is a password defined on the unit. The copyright information displayed upon connection to the IP Link product via TCP/IP or Telnet is followed by the password prompt. The Password: prompt is repeated if a correct administrator or user password is not entered. If a correct administrator or user password is entered, the unit responds with Login Administrator or Login User , depending on the password issued. If the administrator and user passwords are the same, it defaults to administrator privileges.
Command/response table for SIS commands (continued) Command ASCII (Telnet) URL Encoded (Web) Response Ethernet data port Set current connected port timeout Esc 0 * X69 TC W 0 %2A X69 TC| Pti 0 * X69 View current connected port timeout Esc 0TC W0TC| X69 Set global IP port timeout Esc 1 * X69 TC W1%2A X69 TC| Pti1 * X69 View global IP port timeout Esc 1TC W1TC| X69 Remapping port designations Duplicate port# assignments are not permitted; i.e., Telnet and Web cannot be the same. Entering duplicate port assignments results in an E13 (Invalid parameter) error message. Set Telnet port map24 Esc port # MT W port # MT| Pmt port # Reset Telnet port map24 Esc 23MT W23MT| Pmt 00023 Disable Telnet port24 Esc 0MT W0MT| Pmt 00000 View Telnet port map Esc MT WMT| port # Set Web port map24 Esc port # MH Wport # MH| Pmh port # Reset Web port map24 Esc 80MH W80MH| Pmh 00080 Disable Web port map24 Esc 0MH W0MH| Pmh 00000 View Web port map Esc MH WMH| port # Set Direct Access port map24 Esc 2001MD W2001MD| Pmd 02001 Disable Direct Access port map24 Esc 0MD W0MD| Pmd 00000 View Direct Access port map Esc MD WMD| port # Remapping of a port number (other than to reset it to the default 80 or 23, or to disable by setting it to 0) must be to port #1024 or higher. Directories Change/create directory Esc path/directory/CJ W path/directory/CJ| Dir path/directory/ A directory does not truly exist until a file has been copied into the path. Move back to root directory Esc / CJ W%2FCJ| Dir / Move up one directory Esc ..CJ W%2E%2ECJ| Dir path/directory/ View current directory Esc CJ WCJ| path/directory/ File commands Erase user-supplied Web page/file24, 28 Esc filename EF W filename EF| Del filename Erase current directory and its files24, 28 Esc /EF W/EF| Ddl Erase current directory and subdirectories24, 28 Esc //EF W//EF| Ddl IPL T PC1 SIS Programming and Control 5-13 PRELIMINARY
Page 1 and 2:
IP Link Power Control Interface IPL
Page 3 and 4:
FCC Class A Notice This equipment h
Page 5 and 6:
Table of Contents Chapter 1 Introdu
Page 7 and 8:
Using the Command/Response Table ..
Page 9 and 10:
IPL T PC1 1 Chapter One Introductio
Page 11 and 12:
Web-based A/V asset management —
Page 13 and 14:
IPL T PC1 2 Chapter Two Installatio
Page 15 and 16:
Reduced air flow — Installation o
Page 17 and 18:
3 COM port (RS-232) — Connect the
Page 19 and 20: Side View Pins: 12345678 Insert Twi
Page 21 and 22: IPL T PC1 3 Chapter Three Front Pan
Page 23 and 24: Setting Up the System Using the Fro
Page 25 and 26: Result — The RS-232 port is conve
Page 27 and 28: IPL T PC1 4 Chapter Four Ethernet C
Page 29 and 30: ARP-S command screen 6. Execute a p
Page 31 and 32: 2. Right-click Local Area Connectio
Page 33 and 34: 7. Set up the PC1’s IP address. S
Page 35 and 36: Passwords must contain 4 to 12 alph
Page 37 and 38: 2. Enter your new information in th
Page 39 and 40: RS-232 port From the drop-boxes in
Page 41 and 42: 3. In the Re-enter Admin Password f
Page 43 and 44: 4. Click Save to save the informati
Page 45 and 46: 2. Click Browse to open a Choose fi
Page 47 and 48: “Set Schedule For” field, displ
Page 49 and 50: 2. In either the Power ON or Power
Page 51 and 52: Adding a directory To add a directo
Page 53 and 54: The figure below shows the HTML cod
Page 55 and 56: Accessing and Using Telnet (Port 23
Page 57 and 58: Network connections 1. Check the ne
Page 59 and 60: IPL T PC1 5 Chapter Five SIS Progr
Page 61 and 62: The error response codes and their
Page 63 and 64: Symbol definitions = CR/LF (carriag
Page 65 and 66: X712 = Time in minutes (0-1440) 0 =
Page 67 and 68: Command/response table for SIS comm
Page 69: Command/response table for SIS comm
Page 73 and 74: Command/response table for SIS comm
Page 75 and 76: IPL T PC1 Appendix A Reference Mate
Page 77 and 78: General Power input ...............
Page 79 and 80: Glossary 10/100Base-T is Ethernet t
Page 81 and 82: IP address is a unique, 32-bit, bin
Page 83 and 84: Extron’s Warranty Extron Electron
show all

Ethernet Configuration and Control, cont'd - Extron Electronics

Create successful ePaper yourself

Delete template?

Save as template?