Ethernet Configuration and Control, cont'd - Extron Electronics

More documents

Recommendations

Info

PRELIMINARY Ethernet Configuration and Control, cont’d 4-32 3. If contact is established with the unit, but the unit’s Web pages cannot be accessed by your Web browser, verify (in the Options or Preferences menu) that your Web browser is configured for direct network connection and not set up to use a proxy server. If you are still experiencing problems, call the Extron S3 Sales & Technical Support Hotline. Global Configurator Software The Global Configurator 2 (GC2.3) software is an alternative to using the default Web pages to configure and schedule the PC1. GC2.3 is a free asset management software that enables flexible, centralized, Web-based power management for A/V systems. Using Global Configurator software, administrators can view the immediate status and power level of an output device, schedule actions such as powering on and off, monitor specified conditions, and configure its ports. To download the latest version of Global Configurator 2 from the Extron Web site, 1. Select the Downloads tab on the Extron Web site home page. 2. From the side bar menu at the left of the screen, select Software. 3. On the Download Center page, click the Download link at the right end of the Global Configurator line. 4. Fill in the required information on the next Download Center page, and click the Download GCSWnnn.exe button (where n is the GC2 version number). 5. Click Run on the File Download window. 6. Follow the instructions on the subsequent screens to install GC2.3 on your computer. For instructions on using the GC2.3 software with the PC1, refer to the IPL T PC1 Setup Guide, provided with the PC1, and to the Global Configuration 2 Help program, accessible from the GC2.3 main screen. IPL T PC1 Ethernet Configuration and Control GC 2.3 is the minimum version required to configure the PC1.
IPL T PC1 5 Chapter Five SIS Programming and Control Host-to-interface Communications Using the Command/Response Tables
Page 1 and 2:
IP Link Power Control Interface IPL
Page 3 and 4:
FCC Class A Notice This equipment h
Page 5 and 6:
Table of Contents Chapter 1 Introdu
Page 7 and 8: Using the Command/Response Table ..
Page 9 and 10: IPL T PC1 1 Chapter One Introductio
Page 11 and 12: Web-based A/V asset management —
Page 13 and 14: IPL T PC1 2 Chapter Two Installatio
Page 15 and 16: Reduced air flow — Installation o
Page 17 and 18: 3 COM port (RS-232) — Connect the
Page 19 and 20: Side View Pins: 12345678 Insert Twi
Page 21 and 22: IPL T PC1 3 Chapter Three Front Pan
Page 23 and 24: Setting Up the System Using the Fro
Page 25 and 26: Result — The RS-232 port is conve
Page 27 and 28: IPL T PC1 4 Chapter Four Ethernet C
Page 29 and 30: ARP-S command screen 6. Execute a p
Page 31 and 32: 2. Right-click Local Area Connectio
Page 33 and 34: 7. Set up the PC1’s IP address. S
Page 35 and 36: Passwords must contain 4 to 12 alph
Page 37 and 38: 2. Enter your new information in th
Page 39 and 40: RS-232 port From the drop-boxes in
Page 41 and 42: 3. In the Re-enter Admin Password f
Page 43 and 44: 4. Click Save to save the informati
Page 45 and 46: 2. Click Browse to open a Choose fi
Page 47 and 48: “Set Schedule For” field, displ
Page 49 and 50: 2. In either the Power ON or Power
Page 51 and 52: Adding a directory To add a directo
Page 53 and 54: The figure below shows the HTML cod
Page 55 and 56: Accessing and Using Telnet (Port 23
Page 57: Network connections 1. Check the ne
Page 61 and 62: The error response codes and their
Page 63 and 64: Symbol definitions = CR/LF (carriag
Page 65 and 66: X712 = Time in minutes (0-1440) 0 =
Page 67 and 68: Command/response table for SIS comm
Page 75 and 76: IPL T PC1 Appendix A Reference Mate
Page 77 and 78: General Power input ...............
Page 79 and 80: Glossary 10/100Base-T is Ethernet t
Page 81 and 82: IP address is a unique, 32-bit, bin
Page 83 and 84: Extron’s Warranty Extron Electron
show all

Ethernet Configuration and Control, cont'd - Extron Electronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?