Ethernet Configuration and Control, cont'd - Extron Electronics

More documents

Recommendations

Info

PRELIMINARY Ethernet Configuration and Control, cont’d 4-8 4. IP, gateway, and subnet mask addresses follow standard naming and numbering conventions and protocol (xxx.xxx.xxx.xxx). Your IP network administrator should provide the addresses to be used with this interface. Enter the new IP address assigned for the PC1, the corresponding subnet mask, and gateway address, then click Submit. The PC1 can takes up to 2 minutes to store the new settings. Once the interface’s IP address is changed, your PC loses communication with the PC1, and a screen appears, indicating that the page cannot be displayed. 5. Close the browser. 6. After changing the PC1’s IP settings, restore your PC’s TCP/IP settings to their original configuration, and reboot if necessary. (Refer to the addresses you wrote down in step 4 of the “Setting up the PC for IP communication” procedure, earlier in this chapter.) You are now able to access the PC1’s web pages to configure the front panel. Using the IPL T PC1 Web Pages The IPL T PC1 features an embedded Web server, which includes factory set Web pages. These pages can be replaced with user-designed files, but the default Web pages provide many basic features for configuring, and controlling the PC1 via a Web browser. This section provides an overview of the embedded Web pages. To access the embedded Web pages, 1. Launch a Web browser (e.g., Internet Explorer) on your connected PC. 2. On the browser’s Address line, enter the PC1’s IP address. If you have previously created a Global Configurator 2 project for the PC1, the Web page opens in the GlobalViewer format. To display it in the default Web page format, enter the PC1’s IP address, followed by /nortxe_index.html. Example: 10.26.188.44/norte_index.html. See the IPL T PC1 Setup Guide, delivered with your PC1, for information on using Global Configurator. If a password has been set, the Enter Network Password dialog box opens. If no password has been set, the PC1 Web page opens, displaying the System Status tab. (Skip steps 3 and 4.) 3. Enter the administrator password in the Password field. Leave the User Name field blank. Password prompt window 4. Click OK. The PC1 Web page is displayed. IPL T PC1 Ethernet Configuration and Control
Passwords must contain 4 to 12 alphanumeric characters. Spaces and non-alphanumeric symbols and are not allowed, and the passwords are case sensitive. Administrators have access to all of the Web pages and are able to make changes to settings. Users can access only the System Status page. Viewing the system status The System Status Web page on the Status tab provides information on the current settings. Changes must be made via the Configuration Web pages or SIS programming commands (see chapter 5, “SIS Programming and Control”). Personnel who have user access can view this page but cannot access the Configuration or File Management tab pages to make changes. The following figure shows an IPL T PC1i System Status web page. System Status screen IPL T PC1 Ethernet Configuration and Control 4-9 PRELIMINARY
Page 1 and 2: IP Link Power Control Interface IPL
Page 3 and 4: FCC Class A Notice This equipment h
Page 5 and 6: Table of Contents Chapter 1 Introdu
Page 7 and 8: Using the Command/Response Table ..
Page 9 and 10: IPL T PC1 1 Chapter One Introductio
Page 11 and 12: Web-based A/V asset management —
Page 13 and 14: IPL T PC1 2 Chapter Two Installatio
Page 15 and 16: Reduced air flow — Installation o
Page 17 and 18: 3 COM port (RS-232) — Connect the
Page 19 and 20: Side View Pins: 12345678 Insert Twi
Page 21 and 22: IPL T PC1 3 Chapter Three Front Pan
Page 23 and 24: Setting Up the System Using the Fro
Page 25 and 26: Result — The RS-232 port is conve
Page 27 and 28: IPL T PC1 4 Chapter Four Ethernet C
Page 29 and 30: ARP-S command screen 6. Execute a p
Page 31 and 32: 2. Right-click Local Area Connectio
Page 33: 7. Set up the PC1’s IP address. S
Page 37 and 38: 2. Enter your new information in th
Page 39 and 40: RS-232 port From the drop-boxes in
Page 41 and 42: 3. In the Re-enter Admin Password f
Page 43 and 44: 4. Click Save to save the informati
Page 45 and 46: 2. Click Browse to open a Choose fi
Page 47 and 48: “Set Schedule For” field, displ
Page 49 and 50: 2. In either the Power ON or Power
Page 51 and 52: Adding a directory To add a directo
Page 53 and 54: The figure below shows the HTML cod
Page 55 and 56: Accessing and Using Telnet (Port 23
Page 57 and 58: Network connections 1. Check the ne
Page 59 and 60: IPL T PC1 5 Chapter Five SIS Progr
Page 61 and 62: The error response codes and their
Page 63 and 64: Symbol definitions = CR/LF (carriag
Page 65 and 66: X712 = Time in minutes (0-1440) 0 =
Page 67 and 68: Command/response table for SIS comm
Page 75 and 76: IPL T PC1 Appendix A Reference Mate
Page 77 and 78: General Power input ...............
Page 79 and 80: Glossary 10/100Base-T is Ethernet t
Page 81 and 82: IP address is a unique, 32-bit, bin
Page 83 and 84: Extron’s Warranty Extron Electron

Ethernet Configuration and Control, cont'd - Extron Electronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?