Ethernet Configuration and Control, cont'd - Extron Electronics
Ethernet Configuration and Control, cont'd - Extron Electronics Ethernet Configuration and Control, cont'd - Extron Electronics
PRELIMINARY Ethernet Configuration and Control, cont’d 4-6 4. Write down your PC’s current IP address and subnet mask below. You will need to restore these settings to the PC later. If Obtain an IP address automatically has been selected, make a note of that. If not, write down the following: IP address: __________________________ Subnet mask: __________________________ 5. On the Internet Protocol (TCP/IP) Properties window, change your computer’s IP address temporarily so that it can communicate with the PC1: a. Select the “Use the following IP address:” radio button. b. Enter the following values as shown on the next page: IP address: 192.168.254.253 Subnet mask: 255.255.0.0 Default gateway: Blank or 0.0.0.0 (The temporary IP address differs from the PC1’s factory default by one digit.) Internet Protocol (TCP/IP) Properties window for Windows XP c. Click OK to save the changes, and exit the network setup. d. Reboot the PC, if required for the changes to become effective. 6. Plug one end of a Category 5 network/Ethernet crossover cable into the Ethernet (LAN) connector on the PC1 rear panel. (See chapter 2, “Installation and Rear Panel,” for information on the RJ-45 LAN connector wiring.) Plug the other end of the Ethernet cable into the Ethernet port on the PC. IPL T PC1 Ethernet Configuration and Control If you are using a network hub or switch between the PC and the PC1, use a straight-through Category 5 cable instead of a crossover cable.
7. Set up the PC1’s IP address. See “Configuring the IPL T PC1 using a Web browser,” below, for the procedure. Once the PC1 has been reconfigured, you can subsequently use an Ethernet (intranet or Internet) connection to configure or control it. Both your computer and the PC1 must be connected to the same LAN. Configuring the IPL T PC1 using a Web browser The default Web pages that are preloaded on the PC1 are compatible with popular Web browsers such as Internet Explorer (version 5.5 or higher). The following instructions assume that you have configured the Windowsbased PC, connected it to the PC1’s LAN port, and powered on the interface. 1. Obtain a valid IP address, subnet mask, and gateway address for the PC1 from your network administrator. 2. Launch a Web browser (such as Internet Explorer) on the connected PC (for which you set up the network configuration earlier), and enter the PC1’s default address, http://192.168.254.254, in the address box. The PC1’s default Web page is displayed. 3. Select the Configuration tab, then select System Settings from the side bar menu on the left of the screen. The PC1 System Settings page appears, showing the default IP address. System Settings page with default IP address IPL T PC1 Ethernet Configuration and Control 4-7 PRELIMINARY
- Page 1 and 2: IP Link Power Control Interface IPL
- Page 3 and 4: FCC Class A Notice This equipment h
- Page 5 and 6: Table of Contents Chapter 1 Introdu
- Page 7 and 8: Using the Command/Response Table ..
- Page 9 and 10: IPL T PC1 1 Chapter One Introductio
- Page 11 and 12: Web-based A/V asset management —
- Page 13 and 14: IPL T PC1 2 Chapter Two Installatio
- Page 15 and 16: Reduced air flow — Installation o
- Page 17 and 18: 3 COM port (RS-232) — Connect the
- Page 19 and 20: Side View Pins: 12345678 Insert Twi
- Page 21 and 22: IPL T PC1 3 Chapter Three Front Pan
- Page 23 and 24: Setting Up the System Using the Fro
- Page 25 and 26: Result — The RS-232 port is conve
- Page 27 and 28: IPL T PC1 4 Chapter Four Ethernet C
- Page 29 and 30: ARP-S command screen 6. Execute a p
- Page 31: 2. Right-click Local Area Connectio
- Page 35 and 36: Passwords must contain 4 to 12 alph
- Page 37 and 38: 2. Enter your new information in th
- Page 39 and 40: RS-232 port From the drop-boxes in
- Page 41 and 42: 3. In the Re-enter Admin Password f
- Page 43 and 44: 4. Click Save to save the informati
- Page 45 and 46: 2. Click Browse to open a Choose fi
- Page 47 and 48: “Set Schedule For” field, displ
- Page 49 and 50: 2. In either the Power ON or Power
- Page 51 and 52: Adding a directory To add a directo
- Page 53 and 54: The figure below shows the HTML cod
- Page 55 and 56: Accessing and Using Telnet (Port 23
- Page 57 and 58: Network connections 1. Check the ne
- Page 59 and 60: IPL T PC1 5 Chapter Five SIS Progr
- Page 61 and 62: The error response codes and their
- Page 63 and 64: Symbol definitions = CR/LF (carriag
- Page 65 and 66: X712 = Time in minutes (0-1440) 0 =
- Page 67 and 68: Command/response table for SIS comm
- Page 69 and 70: Command/response table for SIS comm
- Page 71 and 72: Command/response table for SIS comm
- Page 73 and 74: Command/response table for SIS comm
- Page 75 and 76: IPL T PC1 Appendix A Reference Mate
- Page 77 and 78: General Power input ...............
- Page 79 and 80: Glossary 10/100Base-T is Ethernet t
- Page 81 and 82: IP address is a unique, 32-bit, bin
7. Set up the PC1’s IP address. See “Configuring the IPL T PC1 using a Web<br />
browser,” below, for the procedure.<br />
Once the PC1 has been reconfigured, you can subsequently use an <strong>Ethernet</strong><br />
(intranet or Internet) connection to configure or control it.<br />
Both your computer <strong>and</strong> the PC1 must be connected to the same LAN.<br />
Configuring the IPL T PC1 using a Web browser<br />
The default Web pages that are preloaded on the PC1 are compatible with popular<br />
Web browsers such as Internet Explorer (version 5.5 or higher).<br />
The following instructions assume that you have configured the Windowsbased<br />
PC, connected it to the PC1’s LAN port, <strong>and</strong> powered on the interface.<br />
1. Obtain a valid IP address, subnet mask, <strong>and</strong> gateway address for the PC1<br />
from your network administrator.<br />
2. Launch a Web browser (such as Internet Explorer) on the connected PC (for<br />
which you set up the network configuration earlier), <strong>and</strong> enter the PC1’s<br />
default address, http://192.168.254.254, in the address box. The PC1’s default<br />
Web page is displayed.<br />
3. Select the <strong>Configuration</strong> tab, then select System Settings from the side bar<br />
menu on the left of the screen. The PC1 System Settings page appears,<br />
showing the default IP address.<br />
System Settings page with default IP address<br />
IPL T PC1 <strong>Ethernet</strong> <strong>Configuration</strong> <strong>and</strong> <strong>Control</strong><br />
4-7<br />
PRELIMINARY