Ethernet Configuration and Control, cont'd - Extron Electronics

More documents

Recommendations

Info

PRELIMINARY Installation and Rear Panel, cont’d 2-8 6 Input contact closure port — Connect a contact closure device to pins 1 (IN, for input) and 2 ( , for ground) of this shared captive screw connector to enable the PC1 to detect a closed circuit between an input and ground and to trigger an event. For example, if a button were pressed or motion were detected by a sensor, the input would short to ground, which would cause an event such as a bell ringing, a light turning on, and/or an e-mail notification that an event has occurred. Wiring the contact Input port 7 The IPL T PC1 contact closure Input port can be connected to any device providing a closure to ground (closed = logic 1 and open = logic 0). The contact Input is connected to 5VDC via a 1k ohm pull-up resistor and must be wired with a ground. This allows the input to be tied to a device such as a motion detector, alarm, photo eye, etc. You can define what this input will trigger via GC2.3. 1. Connect one end of the input cable to a 3.5 mm, 5-pole captive screw connector, wired appropriately, and plug it into pins 1 and 2 of the shared input/IR port connector on the rear panel. 2. Connect the other end of the input cable to the input device that will provide a triggering signal. (See the diagram at right.) Output power receptacle — Connect the power cord from an output device to this three-prong female Edison (IPL T PC1) or IEC (IPL T PC1i) power output receptacle. Connecting the Hardware Connect the cables to the rear panel as follows: 1. Plug an IEC power cord into a wall outlet and into the 3-prong male power connector on the PC1 rear panel. The green Power LED lights and remain lit. 2. Plug the Ethernet cable from the network into the LAN port on the rear panel. The Link LED lights green. 3. Plug the power cord of the output device to be controlled into the output receptacle on the PCI rear panel. 4. If desired, connect the output device to the RS-232 COM port. 5. If desired, connect an IR emitter to the IR port to control an output device. 6. If desired, connect a contact switch to the contact input port. IPL T PC1 Installation and Rear Panel INPUT IR IN S G Momentary Switch
IPL T PC1 3 Chapter Three Front Panel Features and Operation Front Panel Features Setting up the System Using the Front Panel Resetting
Page 1 and 2: IP Link Power Control Interface IPL
Page 3 and 4: FCC Class A Notice This equipment h
Page 5 and 6: Table of Contents Chapter 1 Introdu
Page 7 and 8: Using the Command/Response Table ..
Page 9 and 10: IPL T PC1 1 Chapter One Introductio
Page 11 and 12: Web-based A/V asset management —
Page 13 and 14: IPL T PC1 2 Chapter Two Installatio
Page 15 and 16: Reduced air flow — Installation o
Page 17 and 18: 3 COM port (RS-232) — Connect the
Page 19: Side View Pins: 12345678 Insert Twi
Page 23 and 24: Setting Up the System Using the Fro
Page 25 and 26: Result — The RS-232 port is conve
Page 27 and 28: IPL T PC1 4 Chapter Four Ethernet C
Page 29 and 30: ARP-S command screen 6. Execute a p
Page 31 and 32: 2. Right-click Local Area Connectio
Page 33 and 34: 7. Set up the PC1’s IP address. S
Page 35 and 36: Passwords must contain 4 to 12 alph
Page 37 and 38: 2. Enter your new information in th
Page 39 and 40: RS-232 port From the drop-boxes in
Page 41 and 42: 3. In the Re-enter Admin Password f
Page 43 and 44: 4. Click Save to save the informati
Page 45 and 46: 2. Click Browse to open a Choose fi
Page 47 and 48: “Set Schedule For” field, displ
Page 49 and 50: 2. In either the Power ON or Power
Page 51 and 52: Adding a directory To add a directo
Page 53 and 54: The figure below shows the HTML cod
Page 55 and 56: Accessing and Using Telnet (Port 23
Page 57 and 58: Network connections 1. Check the ne
Page 59 and 60: IPL T PC1 5 Chapter Five SIS Progr
Page 61 and 62: The error response codes and their
Page 63 and 64: Symbol definitions = CR/LF (carriag
Page 65 and 66: X712 = Time in minutes (0-1440) 0 =
Page 67 and 68: Command/response table for SIS comm
Page 69 and 70: Command/response table for SIS comm
Page 71 and 72:
Command/response table for SIS comm
Page 73 and 74:
Command/response table for SIS comm
Page 75 and 76:
IPL T PC1 Appendix A Reference Mate
Page 77 and 78:
General Power input ...............
Page 79 and 80:
Glossary 10/100Base-T is Ethernet t
Page 81 and 82:
IP address is a unique, 32-bit, bin
Page 83 and 84:
Extron’s Warranty Extron Electron
show all

Ethernet Configuration and Control, cont'd - Extron Electronics

Create successful ePaper yourself

Delete template?

Save as template?