Original Instruction Manual - Evolution Power Tools Ltd.

More documents

Recommendations

Info

Fig. 17 Fig. 18 Close up of Mitre pointer fixing screw PREPARING TO MAKE A CUT DO NOT OVER-REACH 22 www.evolutionpowertools.com Keep good footing and balance. Stand to one side so that your face and body are out of line of a possible kickback. Freehand cutting is a major cause of accidents and MUST NOT BE ATTEMPTED. • Ensure that the workpiece is always firmly resting against the fence, and where practical is clamped with the Hold Down Clamp to the table. • The saw table should be clean and free from any sawdust etc. before the workpiece is clamped into position. • Ensure that the ‘cut-off’ material is free to move sideways away from the blade when the cut is completed. Ensure that the ‘cut-off’ piece cannot become ‘jammed’ in any other part of the machine. • Do not use this saw to cut small pieces. If the workpiece being cut would cause your hand or fingers to be within 150mm of the sawblade, the workpiece is too small.
Fig. 19 Close up view of Cutting Handle switches Fig. 20 Fig.21 Fig. 22 THE MOTOR ON/OFF SWITCH (Fig. 19) The ON/OFF Motor Trigger Switch is a non-latching type. It is the upper of the two switches that are positioned inside the Cutting HANDLE. • Press the switch to start the motor. • Release the switch to turn off the motor. CHOP CUTTING This type of cut is used mainly for cutting small or narrow section material. The Cutting Head is gently pushed down to cut through the workpiece. The Sliding Carriage should be locked in its rearmost position. (Fig. 20) • Slide the Cutting Head to the rear as far as it will go. • Tighten the slide lock screw. (Fig. 21) • Place the workpiece on the table and against the fence and secure with clamp(s) as appropriate. • Grasp the saw handle. • Turn the motor on and allow the saw blade to reach full speed. • Press the lower guard locking trigger to release the Cutting Head. The Lower Guard Locking Trigger (Fig. 22) • Lower the Cutting Handle downwards and cut through the workpiece. • Allow the speed of the blade to do the work, there is no need to apply undue pressure to the Cutting Handle. • When the cut has been completed, release the ON/OFF trigger switch. • Allow the blade to come to a complete stop. • Allow the Cutting Head to rise to its upper position, with the lower blade guard completely covering the blade teeth, and the Cutting Head locked in the upper position, before releasing the Cutting Handle. • Remove the workpiece www.evolutionpowertools.com 23
Page 1 and 2: TCT Multipurpose Sliding Mitre Saw
Page 3 and 4: STEALTH 210 FURY3 & STEALTH SPECIAL
Page 5 and 6: INTRODUCTION Congratulations on you
Page 7 and 8: When fitted with a correct blade th
Page 9 and 10: e) Do not overreach. Keep proper fo
Page 11 and 12: WARNING: If any parts are missing,
Page 13 and 14: OVERALL VIEW OF MITER SAW (10) (11)
Page 15 and 16: Fig. 4 Fig. 5 Diagram showing locat
Page 17 and 18: NOTE: The following WARNING labels
Page 19 and 20: OPERATING INSTRUCTIONS CAUTION: The
Page 21: Fig. 14 Close up view of pointer an
Page 25 and 26: Fig. 27 Fig. 28 Mitre Lock Handle F
Page 27 and 28: Fig. 34 Fig. 35 View of guard opera
Page 29 and 30: Fig. 40 Dust Bag being fitted Fig.
Page 31 and 32: FINAL SAFETY CHECKS Condition Yes S
Page 33 and 34: YOUR NOTES www.evolutionpowertools.
Page 35 and 36: EC DECLARATION OF CONFORMITY In acc
Page 37 and 38: EC DECLARATION OF CONFORMITY In acc

Original Instruction Manual - Evolution Power Tools Ltd.

Create successful ePaper yourself

Delete template?

Save as template?