EDR810H/EDR810M EDR410H/EDR410M - EverFocus

More documents

Recommendations

Info

3. LOG: ON: Select ON if you wish to record Alarm Events in the Log. OFF: Select OFF if you do not wish to record Alarm Events in the Log. 4. ACTIVE CAMERA: This field is to activate camera you want to have the alarm enabled too. For example if you had an external motion detector on camera one you would set this option to camera one. The Default from the factory is set to on. To change this, simply use the Jog Dial on the DVR. Active camera setting, from camera 01~08. You can set the camera which corresponds to the place where the alarm is located. Note: The recording camera number in an event depends on the alarm number, and the active camera images will not be recorded. Example: You assign camera 3 as the active camera to alarm 1. When the alarm 1 is triggered, camera 3 will be displayed and camera 1 will be recorded. 5. PTZ PRESET: Select PTZ PRESET from “001” to “255”, so that when Alarm occurs, speed dome will turn to this preset position for event recording. This function improves surveillance quality of an alarm event. If you wish to disable this function, please simply select “OFF”. 6. DURATION: 1~99 SEC: The amount of time alarm recording, screen change, buzzer and output contact will last. Adjustable from 1 ~ 99 seconds. TRANSPARENT: Continuous recording, screen change, buzzer, and output contact for an alarm event. 7. ALARM OUTPUT: This will transmit a signal to another device. The setting of alarms are NONE = not activated, 1 = output signal 1 transmitted. 8. ALARM EMAIL: YES: Send an email when an alarm occurs. NO: Do not send an email when an alarm occurs. The email address and e-mail server can be set in the NETWORK SETUP MENU. 9. BUZZER: Audible alarm buzzer. ENABLE: To enable an alarm buzzer. DISABLE: To disable an alarm buzzer.
10. ALARM NETWORK: YES: Enable alarm network. NO: Disable alarm network. 11. MAIN MON: Display on a main monitor when an alarm occurs. NO CHANGE: No change on the display in the main monitor when an alarm occurs. FULLSCREEN: A full screen of the active camera will display when an alarm occurs. 12. CALL MON: Display on a call monitor when an alarm occurs. NO CHANGE: No change on the display in the main monitor when an alarm occurs. CAMERA 1~8: Display the active camera in full screen mode to the call monitor. 13. SUMMARY: Dial Jog to change items in the SUMMARY table. All alarm’s statuses are shown in SUMMARY tables. These tables are for checking alarm overall statuses, but not for changing them. Note: Please check APPENDIX B to see other available alarm input / output functions.
Page 1 and 2: Instruction Manual EDR810H/EDR810M
Page 3: Federal Communication Commission In
Page 6 and 7: 4.2 SCHEDULE RECORDING SETUP.......
Page 8 and 9: Safety Warning WARNING TO REDUCE RI
Page 10 and 11: Safety Precautions Read Instructio
Page 12 and 13: 1.2 Specifications Video format NTS
Page 14 and 15: 9 FULL: Press this key and channel
Page 16 and 17: 1.4 Back Panel Connections Back pan
Page 18 and 19: LAN 7 LAN Connector: RJ-45 network
Page 20 and 21: 1 Channel tag: A channel tag indica
Page 22 and 23: 3. Event The current/last event tha
Page 24 and 25: 2.1 Basic Wiring Instructions Pleas
Page 26 and 27: 2.2 Hard Disk Drive Installation Th
Page 28 and 29: Unpack Everything Make sure you hav
Page 30 and 31: Possible Installation Locations Ins
Page 32 and 33: 3. DVR Menu Setup Assuming you have
Page 34 and 35: 5. DAYLIGHT SAVING: This field repr
Page 36 and 37: Alaska Standard Time subtract 9 hou
Page 38 and 39: 4. SEQ (MAIN/CALL): Set the number
Page 40 and 41: 7. SUMMARY: Diagram 3.5 Dial Jog to
Page 42 and 43: 4. WATER MARK: ON: Recording is ove
Page 46 and 47: 3.5 Motion Setup Menu Diagram 3.8 D
Page 48 and 49: To edit a MOTION AREA, enter a desi
Page 50 and 51: 5. ALARM EMAIL: Select “YES” fo
Page 52 and 53: 2. IP Address This field shows the
Page 54 and 55: 3.7.2 ALARM NETWORK DVR can send ou
Page 56 and 57: 7. SENDER EMAIL ADDR Input sender
Page 58 and 59: Shared: need shared key. WEP: uses
Page 60 and 61: 3.7.7 DDNS In DDNS of the NETWORK S
Page 62 and 63: 3.7.8 GPS In GPS of the NETWORK SET
Page 64 and 65: 3. END: This field is used to set t
Page 66 and 67: 2. THERMOMETRIC SCALE: Select CELSI
Page 68 and 69: RS485: 5. RS485 Baud Rate: This fie
Page 70 and 71: 4. NETWORK ALARM: YES: To enable ne
Page 72 and 73: 3.11.3 NO HDD In NO HDD, we define:
Page 74 and 75: 4. NETWORK ALARM: YES: To enable ne
Page 76 and 77: 4. UPDATE SYSTEM SOFTWARE: Turn the
Page 78 and 79: 4. Recording Overview Before contin
Page 80 and 81: 4.3 Event Recording Setup We will d
Page 82 and 83: Note: 1. If you only want to record
Page 84 and 85: (3) Fast Forward/Reverse Playback P
Page 86 and 87: 5.2 Search Playback SEARCH Press th
Page 88 and 89: The event types and number show on
Page 90 and 91: In the COPY MENU, we define: Diagra
Page 92 and 93: 7. Call Overview This chapter will
Page 94 and 95:
When turning SHARPNESS OFF, the ima
Page 96 and 97:
09 10. Networking Overview This cha
Page 98 and 99:
Note: Everfocus suggests having a m
Page 100 and 101:
10.7 Simple One to One Connection C
Page 105 and 106:
Once you have reached this point cl
Page 107 and 108:
Now Log into the EverFocus DVR menu
Page 109 and 110:
Connection Procedure: The First st
Page 111 and 112:
11. Linksys Port Forwarding Chapter
Page 113 and 114:
application. Enable - Click the Ena
Page 115 and 116:
12. D-Link Port Forwarding Chapter
Page 117 and 118:
Name - Enter the name referencing t
Page 119 and 120:
13. EverFocus DDNS Setup Note: You
Page 121 and 122:
14. Viewing through Internet Explor
Page 123 and 124:
Click the Security tab at the top,
Page 125 and 126:
The followings are a brief descript
Page 127 and 128:
14.1 SEARCH 14.1.1 Search by Time T
Page 129 and 130:
14.2 PTZ control 1. Select the PTZ
Page 131 and 132:
1) Press on the M button to change
Page 133 and 134:
III. Open the DVRViewer.exe for loa
Page 135 and 136:
14.4 Remote Configuration Click on
Page 137 and 138:
CAMERA setup menu RECORD setup menu
Page 139 and 140:
NETWORK 1 setup menu The Network Co
Page 141 and 142:
WARNING setup menu SYSTEM setup men
Page 143 and 144:
15.2 Remote Control Protocol A comp
Page 145 and 146:
0x23 CH8 0x24 (reserve) 0x25 (reser
Page 147 and 148:
Appendix B: Alarm Board Configurati
Page 149 and 150:
Troubleshooting If you have difficu
show all

EDR810H/EDR810M EDR410H/EDR410M - EverFocus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?