EDR810H/EDR810M EDR410H/EDR410M - EverFocus
EDR810H/EDR810M EDR410H/EDR410M - EverFocus EDR810H/EDR810M EDR410H/EDR410M - EverFocus
7. SUMMARY: Diagram 3.5 Dial Jog to change items in the SUMMARY table. All cameras’ statuses are shown in the SUMMARY table. The table is for checking camera overall statuses only, not for changing them. Note: The SUMMARY table also exists in ALARM, MOTION and VLOSS SETUP MENU. All of these SUMMARY tables are also for checking particular overall statuses, not for changing them. 8. Copy camera’s setting from a camera to other cameras: In order to copy the setting from a camera to other cameras, we provide a setting copy function. Press MENU when you finish setting up a camera, and then press COPY. The word “COPIED” will show up in the top right corner of the screen, and it means the settings have been copied. Dial the Jog to the camera you would like to copy to, and then press SEARCH. The settings of the first camera will be copied to the next one, and “PASTED” will show up in the top right corner. NOTE: TITLE, PTZ ID, and INSTALL/COVERT cannot be copied. These 3 options need to be set independently.
3.3 Record Setup Menu Diagram 3.6 Diagram 3.6 is a screen shot of the RECORD SETUP MENU. This menu is for setting up the options for recording. In the RECORD SETUP MENU the following fields are defined as follows: 1. RECORD AUDIO: YES: Audio will be recorded when machine is recording and a microphone is connected. NO: Audio will not be recorded when machine is recording. 2. TIME STAMP: ON: The time stamp will show on both the live and recorded video. OFF: The time stamp will not show on the live or recorded video. 3. TIME STAMP POSITION: BOTTOM: The time stamp will show on the bottom. TOP: The time stamp will show on the top.
- Page 1 and 2: Instruction Manual EDR810H/EDR810M
- Page 3: Federal Communication Commission In
- Page 6 and 7: 4.2 SCHEDULE RECORDING SETUP.......
- Page 8 and 9: Safety Warning WARNING TO REDUCE RI
- Page 10 and 11: Safety Precautions Read Instructio
- Page 12 and 13: 1.2 Specifications Video format NTS
- Page 14 and 15: 9 FULL: Press this key and channel
- Page 16 and 17: 1.4 Back Panel Connections Back pan
- Page 18 and 19: LAN 7 LAN Connector: RJ-45 network
- Page 20 and 21: 1 Channel tag: A channel tag indica
- Page 22 and 23: 3. Event The current/last event tha
- Page 24 and 25: 2.1 Basic Wiring Instructions Pleas
- Page 26 and 27: 2.2 Hard Disk Drive Installation Th
- Page 28 and 29: Unpack Everything Make sure you hav
- Page 30 and 31: Possible Installation Locations Ins
- Page 32 and 33: 3. DVR Menu Setup Assuming you have
- Page 34 and 35: 5. DAYLIGHT SAVING: This field repr
- Page 36 and 37: Alaska Standard Time subtract 9 hou
- Page 38 and 39: 4. SEQ (MAIN/CALL): Set the number
- Page 42 and 43: 4. WATER MARK: ON: Recording is ove
- Page 44 and 45: 3. LOG: ON: Select ON if you wish t
- Page 46 and 47: 3.5 Motion Setup Menu Diagram 3.8 D
- Page 48 and 49: To edit a MOTION AREA, enter a desi
- Page 50 and 51: 5. ALARM EMAIL: Select “YES” fo
- Page 52 and 53: 2. IP Address This field shows the
- Page 54 and 55: 3.7.2 ALARM NETWORK DVR can send ou
- Page 56 and 57: 7. SENDER EMAIL ADDR Input sender
- Page 58 and 59: Shared: need shared key. WEP: uses
- Page 60 and 61: 3.7.7 DDNS In DDNS of the NETWORK S
- Page 62 and 63: 3.7.8 GPS In GPS of the NETWORK SET
- Page 64 and 65: 3. END: This field is used to set t
- Page 66 and 67: 2. THERMOMETRIC SCALE: Select CELSI
- Page 68 and 69: RS485: 5. RS485 Baud Rate: This fie
- Page 70 and 71: 4. NETWORK ALARM: YES: To enable ne
- Page 72 and 73: 3.11.3 NO HDD In NO HDD, we define:
- Page 74 and 75: 4. NETWORK ALARM: YES: To enable ne
- Page 76 and 77: 4. UPDATE SYSTEM SOFTWARE: Turn the
- Page 78 and 79: 4. Recording Overview Before contin
- Page 80 and 81: 4.3 Event Recording Setup We will d
- Page 82 and 83: Note: 1. If you only want to record
- Page 84 and 85: (3) Fast Forward/Reverse Playback P
- Page 86 and 87: 5.2 Search Playback SEARCH Press th
- Page 88 and 89: The event types and number show on
3.3 Record Setup Menu<br />
Diagram 3.6<br />
Diagram 3.6 is a screen shot of the RECORD SETUP MENU. This menu is for setting up the<br />
options for recording. In the RECORD SETUP MENU the following fields are defined as<br />
follows:<br />
1. RECORD AUDIO:<br />
YES: Audio will be recorded when machine is recording and a microphone is connected.<br />
NO: Audio will not be recorded when machine is recording.<br />
2. TIME STAMP:<br />
ON: The time stamp will show on both the live and recorded video.<br />
OFF: The time stamp will not show on the live or recorded video.<br />
3. TIME STAMP POSITION:<br />
BOTTOM: The time stamp will show on the bottom.<br />
TOP: The time stamp will show on the top.