EDR810H/EDR810M EDR410H/EDR410M - EverFocus
EDR810H/EDR810M EDR410H/EDR410M - EverFocus EDR810H/EDR810M EDR410H/EDR410M - EverFocus
LAN 7 LAN Connector: RJ-45 network connection. RS232 8 RS232 connector: D-Sub 9-pin connector to RS232 ports for testing purpose ONLY. RS485 9 RS485 connector: RJ 45 Connector to cascade/control multi Digital Video Recorders. Remote 10 Remote Control: Remote control port allows for an extension wire with an IR receiver instead of the IR receiver on the front panel. Note: The IR receiver extension line (10m) must be purchased separately. Wireless LAN 11 Antenna: Integrated IEEE 802.11b/g wireless LAN capabilities. The antenna port is for wireless network antenna use (For EDR 410M and 810M only). Fan 12 Fan: Cooling fan.
2. Event sign 1.5 Monitor Display The status information of the cameras or machine will show up, and be located at different places on the screen. For mobile model only: 6. GPS orientation 1. Channel tag 3. Select sign 4. Play status bar 5. Record status bar
- Page 1 and 2: Instruction Manual EDR810H/EDR810M
- Page 3: Federal Communication Commission In
- Page 6 and 7: 4.2 SCHEDULE RECORDING SETUP.......
- Page 8 and 9: Safety Warning WARNING TO REDUCE RI
- Page 10 and 11: Safety Precautions Read Instructio
- Page 12 and 13: 1.2 Specifications Video format NTS
- Page 14 and 15: 9 FULL: Press this key and channel
- Page 16 and 17: 1.4 Back Panel Connections Back pan
- Page 20 and 21: 1 Channel tag: A channel tag indica
- Page 22 and 23: 3. Event The current/last event tha
- Page 24 and 25: 2.1 Basic Wiring Instructions Pleas
- Page 26 and 27: 2.2 Hard Disk Drive Installation Th
- Page 28 and 29: Unpack Everything Make sure you hav
- Page 30 and 31: Possible Installation Locations Ins
- Page 32 and 33: 3. DVR Menu Setup Assuming you have
- Page 34 and 35: 5. DAYLIGHT SAVING: This field repr
- Page 36 and 37: Alaska Standard Time subtract 9 hou
- Page 38 and 39: 4. SEQ (MAIN/CALL): Set the number
- Page 40 and 41: 7. SUMMARY: Diagram 3.5 Dial Jog to
- Page 42 and 43: 4. WATER MARK: ON: Recording is ove
- Page 44 and 45: 3. LOG: ON: Select ON if you wish t
- Page 46 and 47: 3.5 Motion Setup Menu Diagram 3.8 D
- Page 48 and 49: To edit a MOTION AREA, enter a desi
- Page 50 and 51: 5. ALARM EMAIL: Select “YES” fo
- Page 52 and 53: 2. IP Address This field shows the
- Page 54 and 55: 3.7.2 ALARM NETWORK DVR can send ou
- Page 56 and 57: 7. SENDER EMAIL ADDR Input sender
- Page 58 and 59: Shared: need shared key. WEP: uses
- Page 60 and 61: 3.7.7 DDNS In DDNS of the NETWORK S
- Page 62 and 63: 3.7.8 GPS In GPS of the NETWORK SET
- Page 64 and 65: 3. END: This field is used to set t
- Page 66 and 67: 2. THERMOMETRIC SCALE: Select CELSI
2. Event sign<br />
1.5 Monitor Display<br />
The status information of the cameras or machine will show up, and be located at different places<br />
on the screen.<br />
For mobile model only:<br />
6. GPS<br />
orientation<br />
1. Channel tag<br />
3. Select sign<br />
4. Play status bar<br />
5. Record status bar