EDR810H/EDR810M EDR410H/EDR410M - EverFocus
EDR810H/EDR810M EDR410H/EDR410M - EverFocus EDR810H/EDR810M EDR410H/EDR410M - EverFocus
DVR PIN # NAME 1 GND 2 ALM 1 3 ALM 2 4 ALM 3 5 ALM 4 6 ALM 5 7 ALM 6 8 ALM 7 9 ALM 8 10 ----- 11 ----- 12 ----- 13 ----- 14 ----- 15 ----- 16 ----- 17 ----- 18 ALMRSTO 19 REC 20 REC-IN 21 DISKFULL 22 ----- 23 ALM-N.C 24 ALM-N.O 25 ALM-COM HOST PIN # NAME 1 GND 2 ALM 1 3 ALM 2 4 ALM 3 5 ALM 4 6 ALM 5 7 ALM 6 8 GDN 9 ALM 7 10 ALM 8 11 ----- 12 ----- 13 ----- 14 ----- 15 ----- 16 ----- 17 ----- 18 ----- 19 ALMRST 20 REC-IN 21 GND 22 ----- 23 DISKFULL 24 ----- 25 ALM-N.C 26 ALM-N.O 27 ALM-COM 28 GND
Troubleshooting If you have difficulty operating your system, run through the following checklist to see if you can solve the problem. The DVR will not go into record mode? Make sure the HDD is locked in with the key. Also check to make sure the hard drive is set to Master. A diagram located on the Hard Drive Label will show you how to set the drive to master. The DVR displays no picture? First you should check if the equipment is connected properly. See Chapter 1 for help. The second thing to check is if all the wires work properly. The next step is to verify the recorder and cameras are getting the correct amount of power. There is no display coming from one of the channels on the DVR? The first step is to verify is the problem coming from the recorder or the camera. Simply take a working camera and plug it into the port that seems to not be working. If you see a picture this means the problem is coming from the camera. I cannot connect to the recorder via the internet? 1. Are you using Internet Explorer? 2. Make sure you have downloaded and installed the ActiveX controls. For help with this, see Chapter 14. 3. Are you using the IP address from the Internet Service provider? 4. Does your internet provider block any ports? 5. If you are using a router are the ports in your router opened? (NOTE: Please refer to “Network Setup Menu” section for port settings. For example, HTTP port: 00080, Control port: 01600, Data port: 37260)
- Page 98 and 99: Note: Everfocus suggests having a m
- Page 100 and 101: 10.7 Simple One to One Connection C
- Page 105 and 106: Once you have reached this point cl
- Page 107 and 108: Now Log into the EverFocus DVR menu
- Page 109 and 110: Connection Procedure: The First st
- Page 111 and 112: 11. Linksys Port Forwarding Chapter
- Page 113 and 114: application. Enable - Click the Ena
- Page 115 and 116: 12. D-Link Port Forwarding Chapter
- Page 117 and 118: Name - Enter the name referencing t
- Page 119 and 120: 13. EverFocus DDNS Setup Note: You
- Page 121 and 122: 14. Viewing through Internet Explor
- Page 123 and 124: Click the Security tab at the top,
- Page 125 and 126: The followings are a brief descript
- Page 127 and 128: 14.1 SEARCH 14.1.1 Search by Time T
- Page 129 and 130: 14.2 PTZ control 1. Select the PTZ
- Page 131 and 132: 1) Press on the M button to change
- Page 133 and 134: III. Open the DVRViewer.exe for loa
- Page 135 and 136: 14.4 Remote Configuration Click on
- Page 137 and 138: CAMERA setup menu RECORD setup menu
- Page 139 and 140: NETWORK 1 setup menu The Network Co
- Page 141 and 142: WARNING setup menu SYSTEM setup men
- Page 143 and 144: 15.2 Remote Control Protocol A comp
- Page 145 and 146: 0x23 CH8 0x24 (reserve) 0x25 (reser
- Page 147: Appendix B: Alarm Board Configurati
Troubleshooting<br />
If you have difficulty operating your system, run through the following checklist to see if<br />
you can solve the problem.<br />
The DVR will not go into record mode?<br />
Make sure the HDD is locked in with the key. Also check to make sure the hard drive is<br />
set to Master. A diagram located on the Hard Drive Label will show you how to set the<br />
drive to master.<br />
The DVR displays no picture?<br />
First you should check if the equipment is connected properly. See Chapter 1 for help.<br />
The second thing to check is if all the wires work properly.<br />
The next step is to verify the recorder and cameras are getting the correct amount of<br />
power.<br />
There is no display coming from one of the channels on the DVR?<br />
The first step is to verify is the problem coming from the recorder or the camera.<br />
Simply take a working camera and plug it into the port that seems to not be working. If<br />
you see a picture this means the problem is coming from the camera.<br />
I cannot connect to the recorder via the internet?<br />
1. Are you using Internet Explorer?<br />
2. Make sure you have downloaded and installed the ActiveX controls. For help<br />
with this, see Chapter 14.<br />
3. Are you using the IP address from the Internet Service provider?<br />
4. Does your internet provider block any ports?<br />
5. If you are using a router are the ports in your router opened?<br />
(NOTE: Please refer to “Network Setup Menu” section for port settings. For<br />
example, HTTP port: 00080, Control port: 01600, Data port: 37260)