EDR810H/EDR810M EDR410H/EDR410M - EverFocus

More documents

Recommendations

Info

Use the prior step to assign an IP address. For example, if you got the IP address from the computer of 192.168.002.101. Assign the DVR’s IP address as 192.168.002.050. Now Copy the subnet mask and default gateway information you got from the prior step off the computer to the DVR. Note: Make sure the modem is in bridge mode. If your Internet Service Provider is BellSouth you will have a modem/router. BellSouth provides a Westell modem that includes a built-in router. You will need to disable the router functionality. The next step is to open ports within your router. Open virtual ports in the router (Log into the router using a PC) o EDR Ports to open: 80, 1600, 37260, 37261, 37262, 37263 Note: If your Internet service provider blocks port 80 you may use a different port to access the DVR through the DVR’s Network Menu Setup. Note: If you wish to have multiple users log into the DVR please open a range for the control and data ports on your router. For example if you would only like 4 clients to connect to the DVR open 1600 and 37260 ~ 37263 If you have a Dynamic IP address and have open the ports simply go to Chapter 9 to Configure DDNS. Once you have reached this point and you have restarted the digital recorder. To access the DVR from a computer simply open Internet Explorer and in the address bar type: http:// and the IP address of your internet service provider. Note: If your Internet service provider blocks port 80 you may use a different port to access the DVR through the DVR’s Network Menu Setup.
11. Linksys Port Forwarding Chapter 11 This chapter will cover a few simple configurations for the Linksys router. Please understand we do not support this product and will not give tech support on it. If you need technical support on this router you must call Linksys. This chapter is to offer some help to the installer and end user, nothing more. To access the Web-based Utility, launch Internet Explorer or Netscape Navigator, and enter the Router’s default IP address, 192.168.1.1, in the Address field. Then, press Enter. A password request page will appear. (Non-Windows XP users will see a similar screen.) Leave the User Name field blank. The first time you open the Web-based Utility, use the default password admin. (You can set a new password from the Administration tab’s Management screen.) Click the OK button to continue. The first screen that appears displays the Setup tab. This allows you to change the Router's general settings. Change these settings as described here and click the Save Settings button to apply your changes or Cancel Changes to cancel your changes.
Page 1 and 2:
Instruction Manual EDR810H/EDR810M
Page 3:
Federal Communication Commission In
Page 6 and 7:
4.2 SCHEDULE RECORDING SETUP.......
Page 8 and 9:
Safety Warning WARNING TO REDUCE RI
Page 10 and 11:
Safety Precautions Read Instructio
Page 12 and 13:
1.2 Specifications Video format NTS
Page 14 and 15:
9 FULL: Press this key and channel
Page 16 and 17:
1.4 Back Panel Connections Back pan
Page 18 and 19:
LAN 7 LAN Connector: RJ-45 network
Page 20 and 21:
1 Channel tag: A channel tag indica
Page 22 and 23:
3. Event The current/last event tha
Page 24 and 25:
2.1 Basic Wiring Instructions Pleas
Page 26 and 27:
2.2 Hard Disk Drive Installation Th
Page 28 and 29:
Unpack Everything Make sure you hav
Page 30 and 31:
Possible Installation Locations Ins
Page 32 and 33:
3. DVR Menu Setup Assuming you have
Page 34 and 35:
5. DAYLIGHT SAVING: This field repr
Page 36 and 37:
Alaska Standard Time subtract 9 hou
Page 38 and 39:
4. SEQ (MAIN/CALL): Set the number
Page 40 and 41:
7. SUMMARY: Diagram 3.5 Dial Jog to
Page 42 and 43:
4. WATER MARK: ON: Recording is ove
Page 44 and 45:
3. LOG: ON: Select ON if you wish t
Page 46 and 47:
3.5 Motion Setup Menu Diagram 3.8 D
Page 48 and 49:
To edit a MOTION AREA, enter a desi
Page 50 and 51:
5. ALARM EMAIL: Select “YES” fo
Page 52 and 53:
2. IP Address This field shows the
Page 54 and 55:
3.7.2 ALARM NETWORK DVR can send ou
Page 56 and 57:
7. SENDER EMAIL ADDR Input sender
Page 58 and 59:
Shared: need shared key. WEP: uses
Page 60 and 61: 3.7.7 DDNS In DDNS of the NETWORK S
Page 62 and 63: 3.7.8 GPS In GPS of the NETWORK SET
Page 64 and 65: 3. END: This field is used to set t
Page 66 and 67: 2. THERMOMETRIC SCALE: Select CELSI
Page 68 and 69: RS485: 5. RS485 Baud Rate: This fie
Page 70 and 71: 4. NETWORK ALARM: YES: To enable ne
Page 72 and 73: 3.11.3 NO HDD In NO HDD, we define:
Page 74 and 75: 4. NETWORK ALARM: YES: To enable ne
Page 76 and 77: 4. UPDATE SYSTEM SOFTWARE: Turn the
Page 78 and 79: 4. Recording Overview Before contin
Page 80 and 81: 4.3 Event Recording Setup We will d
Page 82 and 83: Note: 1. If you only want to record
Page 84 and 85: (3) Fast Forward/Reverse Playback P
Page 86 and 87: 5.2 Search Playback SEARCH Press th
Page 88 and 89: The event types and number show on
Page 90 and 91: In the COPY MENU, we define: Diagra
Page 92 and 93: 7. Call Overview This chapter will
Page 94 and 95: When turning SHARPNESS OFF, the ima
Page 96 and 97: 09 10. Networking Overview This cha
Page 98 and 99: Note: Everfocus suggests having a m
Page 100 and 101: 10.7 Simple One to One Connection C
Page 105 and 106: Once you have reached this point cl
Page 107 and 108: Now Log into the EverFocus DVR menu
Page 109: Connection Procedure: The First st
Page 113 and 114: application. Enable - Click the Ena
Page 115 and 116: 12. D-Link Port Forwarding Chapter
Page 117 and 118: Name - Enter the name referencing t
Page 119 and 120: 13. EverFocus DDNS Setup Note: You
Page 121 and 122: 14. Viewing through Internet Explor
Page 123 and 124: Click the Security tab at the top,
Page 125 and 126: The followings are a brief descript
Page 127 and 128: 14.1 SEARCH 14.1.1 Search by Time T
Page 129 and 130: 14.2 PTZ control 1. Select the PTZ
Page 131 and 132: 1) Press on the M button to change
Page 133 and 134: III. Open the DVRViewer.exe for loa
Page 135 and 136: 14.4 Remote Configuration Click on
Page 137 and 138: CAMERA setup menu RECORD setup menu
Page 139 and 140: NETWORK 1 setup menu The Network Co
Page 141 and 142: WARNING setup menu SYSTEM setup men
Page 143 and 144: 15.2 Remote Control Protocol A comp
Page 145 and 146: 0x23 CH8 0x24 (reserve) 0x25 (reser
Page 147 and 148: Appendix B: Alarm Board Configurati
Page 149 and 150: Troubleshooting If you have difficu
show all

EDR810H/EDR810M EDR410H/EDR410M - EverFocus

Create successful ePaper yourself

Delete template?

Save as template?