EDR810H/EDR810M EDR410H/EDR410M - EverFocus
EDR810H/EDR810M EDR410H/EDR410M - EverFocus EDR810H/EDR810M EDR410H/EDR410M - EverFocus
10.9 Router or LAN Connection Internet Cat 5 Straight Through Cable DVR Straight Through Ethernet Cable Pin outs: The Diagram below shows the pin configurations for a straight cable. Diagram 10.3 Hi-speed modem Router
Connection Procedure: The First step is to purchase or make a straight through cable. We recommend purchasing one if you have never made a straight through cable. Please remember you can not use a cross over network cable for this application Once you have a straight through cable plug one end into the LAN port on the back of the recorder and the other into the router. Now Log into the EverFocus DVR menu and using the jog dial from the previous chapter go to the Network Setting Menu. If you have a Linksys Router: Assign an IP address of 192.168.001.050 to the DVR, a Subnet mask of 255.255.255.000, and a default gateway of 192.168.001.001. If you have a D-Link Router: Assign an IP address of 192.168.000.050 to the DVR, a Subnet mask of 255.255.255.000, and a default gateway of 192.168.000.001. If you have a pre-existing LAN: Go to a Computer on the pre-existing network and do the following: o Go to Start, then Run and type cmd and click on OK. Then hit enter, type ipconfig and press enter this will give you the information you will need.
- Page 58 and 59: Shared: need shared key. WEP: uses
- Page 60 and 61: 3.7.7 DDNS In DDNS of the NETWORK S
- Page 62 and 63: 3.7.8 GPS In GPS of the NETWORK SET
- Page 64 and 65: 3. END: This field is used to set t
- Page 66 and 67: 2. THERMOMETRIC SCALE: Select CELSI
- Page 68 and 69: RS485: 5. RS485 Baud Rate: This fie
- Page 70 and 71: 4. NETWORK ALARM: YES: To enable ne
- Page 72 and 73: 3.11.3 NO HDD In NO HDD, we define:
- Page 74 and 75: 4. NETWORK ALARM: YES: To enable ne
- Page 76 and 77: 4. UPDATE SYSTEM SOFTWARE: Turn the
- Page 78 and 79: 4. Recording Overview Before contin
- Page 80 and 81: 4.3 Event Recording Setup We will d
- Page 82 and 83: Note: 1. If you only want to record
- Page 84 and 85: (3) Fast Forward/Reverse Playback P
- Page 86 and 87: 5.2 Search Playback SEARCH Press th
- Page 88 and 89: The event types and number show on
- Page 90 and 91: In the COPY MENU, we define: Diagra
- Page 92 and 93: 7. Call Overview This chapter will
- Page 94 and 95: When turning SHARPNESS OFF, the ima
- Page 96 and 97: 09 10. Networking Overview This cha
- Page 98 and 99: Note: Everfocus suggests having a m
- Page 100 and 101: 10.7 Simple One to One Connection C
- Page 105 and 106: Once you have reached this point cl
- Page 107: Now Log into the EverFocus DVR menu
- Page 111 and 112: 11. Linksys Port Forwarding Chapter
- Page 113 and 114: application. Enable - Click the Ena
- Page 115 and 116: 12. D-Link Port Forwarding Chapter
- Page 117 and 118: Name - Enter the name referencing t
- Page 119 and 120: 13. EverFocus DDNS Setup Note: You
- Page 121 and 122: 14. Viewing through Internet Explor
- Page 123 and 124: Click the Security tab at the top,
- Page 125 and 126: The followings are a brief descript
- Page 127 and 128: 14.1 SEARCH 14.1.1 Search by Time T
- Page 129 and 130: 14.2 PTZ control 1. Select the PTZ
- Page 131 and 132: 1) Press on the M button to change
- Page 133 and 134: III. Open the DVRViewer.exe for loa
- Page 135 and 136: 14.4 Remote Configuration Click on
- Page 137 and 138: CAMERA setup menu RECORD setup menu
- Page 139 and 140: NETWORK 1 setup menu The Network Co
- Page 141 and 142: WARNING setup menu SYSTEM setup men
- Page 143 and 144: 15.2 Remote Control Protocol A comp
- Page 145 and 146: 0x23 CH8 0x24 (reserve) 0x25 (reser
- Page 147 and 148: Appendix B: Alarm Board Configurati
- Page 149 and 150: Troubleshooting If you have difficu
Connection Procedure:<br />
The First step is to purchase or make a straight through cable. We recommend purchasing<br />
one if you have never made a straight through cable. Please remember you can not use a<br />
cross over network cable for this application<br />
Once you have a straight through cable plug one end into the LAN port on the back of the<br />
recorder and the other into the router.<br />
Now Log into the <strong>EverFocus</strong> DVR menu and using the jog dial from the previous chapter go<br />
to the Network Setting Menu.<br />
If you have a Linksys Router:<br />
Assign an IP address of 192.168.001.050 to the DVR, a Subnet mask of<br />
255.255.255.000, and a default gateway of 192.168.001.001.<br />
If you have a D-Link Router:<br />
Assign an IP address of 192.168.000.050 to the DVR, a Subnet mask of<br />
255.255.255.000, and a default gateway of 192.168.000.001.<br />
If you have a pre-existing LAN:<br />
Go to a Computer on the pre-existing network and do the following:<br />
o Go to Start, then Run and type cmd and click on OK.<br />
Then hit enter, type ipconfig and press enter this will give you the information you will<br />
need.
Change language