EDR810H/EDR810M EDR410H/EDR410M - EverFocus

More documents

Recommendations

Info

10.8 Direct High Speed Modem Connection Internet Straight Through Ethernet Cable Pin outs: The Diagram below shows the pin configurations for a straight cable. Connection Procedure: Cat 5 Straight Through Cable Diagram 10.2 Hi-speed modem DVR The First step is to purchase or make a straight through cable. We recommend purchasing one if you have never made a straight through cable. Please remember you can not use a cross over network cable for this application Once you have a straight through cable plug one end into the LAN port on the back of the recorder and the other into the high speed modem.
Now Log into the <strong>EverFocus</strong> DVR menu and using the jog dial from the previous chapter go to the Network Setting Menu. Assign the Static IP address which you obtained from the internet service provider to the DVR, the Subnet mask from the internet service provider to the DVR, and the default gateway of the internet service provider. Note: If you have a dynamic IP address this type of connection will not work for you. You will need to purchase a router or ask your internet service provider for a static IP address. (Please refer to local area network connection checklist) Once you have reached this point click ok and restart both the computer and the digital recorder. To access the DVR from a computer simply open Internet Explorer and in the address bar type: http:// and the IP address of your internet service provider.
Page 1 and 2:
Instruction Manual EDR810H/EDR810M
Page 3:
Federal Communication Commission In
Page 6 and 7:
4.2 SCHEDULE RECORDING SETUP.......
Page 8 and 9:
Safety Warning WARNING TO REDUCE RI
Page 10 and 11:
Safety Precautions Read Instructio
Page 12 and 13:
1.2 Specifications Video format NTS
Page 14 and 15:
9 FULL: Press this key and channel
Page 16 and 17:
1.4 Back Panel Connections Back pan
Page 18 and 19:
LAN 7 LAN Connector: RJ-45 network
Page 20 and 21:
1 Channel tag: A channel tag indica
Page 22 and 23:
3. Event The current/last event tha
Page 24 and 25:
2.1 Basic Wiring Instructions Pleas
Page 26 and 27:
2.2 Hard Disk Drive Installation Th
Page 28 and 29:
Unpack Everything Make sure you hav
Page 30 and 31:
Possible Installation Locations Ins
Page 32 and 33:
3. DVR Menu Setup Assuming you have
Page 34 and 35:
5. DAYLIGHT SAVING: This field repr
Page 36 and 37:
Alaska Standard Time subtract 9 hou
Page 38 and 39:
4. SEQ (MAIN/CALL): Set the number
Page 40 and 41:
7. SUMMARY: Diagram 3.5 Dial Jog to
Page 42 and 43:
4. WATER MARK: ON: Recording is ove
Page 44 and 45:
3. LOG: ON: Select ON if you wish t
Page 46 and 47:
3.5 Motion Setup Menu Diagram 3.8 D
Page 48 and 49:
To edit a MOTION AREA, enter a desi
Page 50 and 51:
5. ALARM EMAIL: Select “YES” fo
Page 52 and 53:
2. IP Address This field shows the
Page 54 and 55:
3.7.2 ALARM NETWORK DVR can send ou
Page 56 and 57: 7. SENDER EMAIL ADDR Input sender
Page 58 and 59: Shared: need shared key. WEP: uses
Page 60 and 61: 3.7.7 DDNS In DDNS of the NETWORK S
Page 62 and 63: 3.7.8 GPS In GPS of the NETWORK SET
Page 64 and 65: 3. END: This field is used to set t
Page 66 and 67: 2. THERMOMETRIC SCALE: Select CELSI
Page 68 and 69: RS485: 5. RS485 Baud Rate: This fie
Page 70 and 71: 4. NETWORK ALARM: YES: To enable ne
Page 72 and 73: 3.11.3 NO HDD In NO HDD, we define:
Page 74 and 75: 4. NETWORK ALARM: YES: To enable ne
Page 76 and 77: 4. UPDATE SYSTEM SOFTWARE: Turn the
Page 78 and 79: 4. Recording Overview Before contin
Page 80 and 81: 4.3 Event Recording Setup We will d
Page 82 and 83: Note: 1. If you only want to record
Page 84 and 85: (3) Fast Forward/Reverse Playback P
Page 86 and 87: 5.2 Search Playback SEARCH Press th
Page 88 and 89: The event types and number show on
Page 90 and 91: In the COPY MENU, we define: Diagra
Page 92 and 93: 7. Call Overview This chapter will
Page 94 and 95: When turning SHARPNESS OFF, the ima
Page 96 and 97: 09 10. Networking Overview This cha
Page 98 and 99: Note: Everfocus suggests having a m
Page 100 and 101: 10.7 Simple One to One Connection C
Page 105: Once you have reached this point cl
Page 109 and 110: Connection Procedure: The First st
Page 111 and 112: 11. Linksys Port Forwarding Chapter
Page 113 and 114: application. Enable - Click the Ena
Page 115 and 116: 12. D-Link Port Forwarding Chapter
Page 117 and 118: Name - Enter the name referencing t
Page 119 and 120: 13. EverFocus DDNS Setup Note: You
Page 121 and 122: 14. Viewing through Internet Explor
Page 123 and 124: Click the Security tab at the top,
Page 125 and 126: The followings are a brief descript
Page 127 and 128: 14.1 SEARCH 14.1.1 Search by Time T
Page 129 and 130: 14.2 PTZ control 1. Select the PTZ
Page 131 and 132: 1) Press on the M button to change
Page 133 and 134: III. Open the DVRViewer.exe for loa
Page 135 and 136: 14.4 Remote Configuration Click on
Page 137 and 138: CAMERA setup menu RECORD setup menu
Page 139 and 140: NETWORK 1 setup menu The Network Co
Page 141 and 142: WARNING setup menu SYSTEM setup men
Page 143 and 144: 15.2 Remote Control Protocol A comp
Page 145 and 146: 0x23 CH8 0x24 (reserve) 0x25 (reser
Page 147 and 148: Appendix B: Alarm Board Configurati
Page 149 and 150: Troubleshooting If you have difficu
show all

EDR810H/EDR810M EDR410H/EDR410M - EverFocus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?