FLEX Series Access Control Management Software - Everfocus

More documents

Recommendations

Info

when the APB property of a card is set as enabled and that card is presented twice consecutively on any enter-door reader or exit-door reader. The controller generates alarm output(s) according to the settings in the “APB Fail” column. • Card PIN Fail: A Card PIN Fail event is generated when a PIN-enabled card is presented at a reader and an incorrect PIN is entered three times consecutively. The controller generates alarm output(s) according to the settings in the “Card PIN error” column. • Door Forced Open: A Door Forced Open event is generated when the door sensor indicates to the controller that a door is opened, but no legitimate card has been presented and a request to exit has not been pressed. The controller generates alarm output(s) according to the settings in the “Forced Open” column. • Overtime: An overtime event occurs when a door is held open for longer than the allowed time (as set by the system administrator). The controller generates alarm output(s) according to the settings in the “Overtime” column. • Reader Lost: A Reader Lost event will be generated when controller detects that the card reader appears to have been disconnected from the system. The controller generates alarm output(s) according to the settings in the “Reader Lost” column. Configure an Alarm All the events can be allocated to any alarm relay output on main module, door module, and alarm module. The detailed configuration method is introduced in this section. 1. Select the Tab that includes the alarm configuration being changed. For example, choose “Alarm Setting 1” for “Fire Alarm”. The “Fire Alarm” column 29
setting is used to configure the outputs when a signal from the Fire Alarm input is activated. 2. To change the “Fire Alarm” setting: a. Point the mouse over the cell being changed. b. Double click the mouse to switch the setting from: Yes to No or vice versa. Yes indicates there is an alarm output (relay energized) No indicates there is no alarm output (relay not energized). Double Click Fig. 4.19 Configure an alarm 3. For the door module alarm configurations under “Alarm setting 3” tab, there is one difference. A third option is introduced only for the door module alarm outputs. Follow the steps bellow: a. Point and click the mouse over the cell being changed. b. For the door module outputs, an option to select from a menu appears, follow the steps as below: Click on the arrow and choose from Y, N or R. 30
Page 1 and 2: EverAccess User’s Manual Volume 1
Page 3 and 4: Table of Contents CHAPTER 1 Introdu
Page 5 and 6: Select a Controller................
Page 7 and 8: Event Warning Message .............
Page 9 and 10: About the software EverAccess Flex
Page 11 and 12: • Free hard drive space: 100M byt
Page 13 and 14: Fig. 2.2 If you wish to change the
Page 15 and 16: Uninstall the program To uninstall
Page 17 and 18: Authority Management Chapter 3 This
Page 19 and 20: Manage Users and Authorities Click
Page 21 and 22: Once the user is successfully added
Page 23 and 24: Controller Configuration This chapt
Page 25 and 26: Fig 4.3 Select the COM port for the
Page 27 and 28: 2. Click the “Modify” button at
Page 29 and 30: 5. Click “Ok” in the cell to ch
Page 31 and 32: Fig. 4.15 Set the system reader pro
Page 33 and 34: A System PIN Fail event will be gen
Page 35: To disable a card, the user can des
Page 39 and 40: Fig. 4.21 Other setting tab Configu
Page 41 and 42: Enable Auto Daylight Saving Time Th
Page 43 and 44: Holiday Setting Chapter 5 This chap
Page 45 and 46: Function button bar Add a Date To a
Page 47 and 48: Edit a Date If a holiday needs to b
Page 49 and 50: 3 1 2 Control Group Setting Dialog
Page 51 and 52: Set Access Authority In this part w
Page 53 and 54: c. Click the box corresponding to t
Page 55 and 56: Download the setting data to contro
Page 57 and 58: 1 3 2 Figure 7.1 Door Access Settin
Page 59 and 60: e. Repeat a, b, c and d to setup al
Page 61 and 62: Example Figure 7.2 An example: door
Page 63 and 64: 2. Adding to the “target controll
Page 65 and 66: 1 2 3 6 4 Figure 8.2 Cardholder man
Page 67 and 68: Close button: press this button to
Page 69 and 70: 5. Once all cards have been registe
Page 71 and 72: 3. Press the button on card attribu
Page 73 and 74: • Phone Number • Email • Posi
Page 75 and 76: Filter Cardholders Figure 8.15: Car
Page 77 and 78: 1. At the uneditable mode of card m
Page 79 and 80: Finger_EN: reserved for fingerprint
Page 81 and 82: Delete Card(s) EverAccess Flex soft
Page 83 and 84: Export Cardholder Reports in HTML f
Page 85 and 86: Figure 8.27 Department data edit wi
Page 87 and 88:
Fig. 9.2 The dialog of data downloa
Page 89 and 90:
5. Click the “Download Now” box
Page 91 and 92:
4. Select one or more controller fr
Page 93 and 94:
Fig. 10.2 The dialog of database ba
Page 95 and 96:
Fig. 10.5 The dialog of database re
Page 97 and 98:
• 1 Month: Delete all records old
Page 99 and 100:
Event Log This chapter covers all E
Page 101 and 102:
• Name: the name of the card hold
Page 103 and 104:
Fig. 11.8 Access granted event logs
Page 105 and 106:
Search Event Logs Users can search
Page 107 and 108:
Fig. 11.11 Adjust the event column
Page 109 and 110:
Fig. 11.14 Export an excel file dia
Page 111 and 112:
Device Control This chapter covers
Page 113 and 114:
Fig. 12.3 Arm/Disarm control To rem
Page 115 and 116:
2. Click the controller address to
Page 117 and 118:
Adding Company Logo and Door Status
Page 119 and 120:
8. To cancel without any change of
Page 121 and 122:
Fig 13.6 A sample of door status ch
Page 123:
Head Office European Office 12F, No
show all

FLEX Series Access Control Management Software - Everfocus

Create successful ePaper yourself

Delete template?

Save as template?