ETC Ion - Theatre Uwinnipeg

More documents

Recommendations

Info

Color indicators <strong>Ion</strong> uses color to indicate the selection state and information about channel or parameter levels. Channel numbers/channel headers Selected Unselected • Gray number . . . . . . . . .Unpatched channel number. • White number . . . . . . . .Selected channel number. • Bright White number . .Channel is parked. • Gold number . . . . . . . . .Channel is captured. • Gold outline . . . . . . . . .Selected channel. • Number with no graphicDeleted channel. Channel or parameter levels • Red. . . . . . . . . . . . . . . . .Manual data (any data that has been set but not yet stored to an active cue or submaster). • Blue . . . . . . . . . . . . . . . .The intensity value is higher than in the previous cue. Non-intensity parameters (NPs) are in blue when any move instruction has occurred. Unmarked. • Green . . . . . . . . . . . . . . .The intensity value is lower than in the previous cue. Also used in reference marking to indicate a channel has just marked. • Magenta. . . . . . . . . . . . .In a mark cue, the recorded value is tracked, unchanged from a previous cue, or in a reference cue, that a stored mark is still intact. • White . . . . . . . . . . . . . . .The value is blocked. • White with an underscoreValue is autoblocked. • Gray . . . . . . . . . . . . . . . .Default or the value is a null value (from either {Make Null} or a filter). When nulled, a gray “n” appears next to the value. • Yellow . . . . . . . . . . . . . .Data set from a submaster. 36 <strong>Ion</strong> Operations Manual
Text Indicators in live/blind Please note examples of text indicators in the following graphic: “B” “_” (underscore) “C” “I” “N” “A” “t” “Ph” “R” “M” “P” “+” “Pr” “Q 10/4” “CP2” “MK” Color conventions listed above apply to text indicators as well. Therefore red indicates a manual value that must be stored. Color conventions listed above apply to text indicators as well. Therefore red indicates a manual value that must be stored. • _ . . . . . . . . . . . . . . . . . . .Underlined value (white) indicates a system-applied block (also called an auto-block). • A. . . . . . . . . . . . . . . . . . .Indicates the channel or parameter is asserted. • B. . . . . . . . . . . . . . . . . . .Indicates the channel or parameter is manually blocked. This block must be stored. • C. . . . . . . . . . . . . . . . . . .Captured Channel • I . . . . . . . . . . . . . . . . . . .Channel is controlled by an inhibitive submaster or grandmaster. When displayed in the Block flag, “I” indicates a cue level intensity block. 3 System Basics 37
Page 1 and 2: Lighting Control Console Operations
Page 3 and 4: Table of Contents Introduction . .
Page 5 and 6: Selective Partial Show Opening . .
Page 7 and 8: Highlight/Lowlight Rem Dim. . . . .
Page 9 and 10: Setting Referenced Mark Flags . . .
Page 11 and 12: Focus Effects . . . . . . . . . . .
Page 13 and 14: MIDI Show Control Devices. . . . .
Page 15 and 16: Introduction Welcome to the Ion Ope
Page 17 and 18: Register Your Ion Registering your
Page 19 and 20: Enter Since the command line can re
Page 21 and 22: Live and Blind Live and Blind are m
Page 23 and 24: Chapter 1 System Overview Inside th
Page 25 and 26: Gateways Ion is part of a fully net
Page 27 and 28: USB Ports One USB port is provided
Page 29 and 30: Outputting DMX In order to output c
Page 31 and 32: Chapter 2 System Installation This
Page 33 and 34: Ion Console Client Software Eos Con
Page 35 and 36: Chapter 3 System Basics This chapte
Page 37 and 38: Power Power Up the Console Note: No
Page 39 and 40: You can use the [Swap] key to chang
Page 41 and 42: The Central Information Area (CIA)
Page 43 and 44: Using the Browser To use the browse
Page 45 and 46: Using Direct Selects Direct selects
Page 47 and 48: Display Control and Navigation Open
Page 49: Graphical User Interface (GUI) Disp
Page 53 and 54: [Data] Key Pressing and holding [Da
Page 55 and 56: Indicators in the Playback Status D
Page 57 and 58: Using [Format] Some displays have m
Page 59 and 60: Spreadsheet (Blind Only) Spreadshee
Page 61 and 62: Chapter 4 Managing Show Files This
Page 63 and 64: Select the specific show file • N
Page 65 and 66: To open only partial components fro
Page 67 and 68: To merge only partial components: S
Page 69 and 70: Saving the Current Show File To sav
Page 71 and 72: Deleting a File Ion provides you wi
Page 73 and 74: Chapter 5 Patch The Patch is where
Page 75 and 76: Displays To begin patching your sho
Page 77 and 78: Create and Edit Patch Select Channe
Page 79 and 80: Dimmer Doubling You can patch chann
Page 81 and 82: Step 6: To select a device interfac
Page 83 and 84: Note: Note: Note: • {RDM Discover
Page 85 and 86: • {Swap} - A moving light attribu
Page 87 and 88: Patch Channels from the Encoder LCD
Page 89 and 90: The picker displays buttons for the
Page 91 and 92: Editing a copy of a scroll or wheel
Page 93 and 94: To calibrate from the LCD: Step 1:
Page 95 and 96: Fixture Creator Ion provides you wi
Page 97 and 98: To add parameters to a new fixture:
Page 99 and 100: To alter the Home settings for any
Page 101 and 102:
Chapter 6 Using Groups Groups are c
Page 103 and 104:
Offset You can use the {Offset} sof
Page 105 and 106:
Using Groups as a Channel Collector
Page 107 and 108:
Chapter 7 Setup This chapter descri
Page 109 and 110:
Show Settings Click {Show Settings}
Page 111 and 112:
Grandmasters, submasters, and playb
Page 113 and 114:
{ACN - MIDI Tx ID} This setting all
Page 115 and 116:
{Manual Control} This desk setting
Page 117 and 118:
{Displays} This desk setting button
Page 119 and 120:
Clicking {Identify} will display nu
Page 121 and 122:
Chapter 8 Basic Manual Control Ion
Page 123 and 124:
[Next] and [Last] The [Next] and [L
Page 125 and 126:
Manual Control of Non-intensity Par
Page 127 and 128:
Encoder LCD screen The encoder LCD
Page 129 and 130:
Min and Max {Min} and {Max} are dis
Page 131 and 132:
Shutter Control Pressing the [Shutt
Page 133 and 134:
Home Ion is equipped with a [Home]
Page 135 and 136:
Lamp Controls Lamp controls allow y
Page 137 and 138:
Remainder Dim [Rem Dim] temporarily
Page 139 and 140:
Highlight and Lowlight Ion can be p
Page 141 and 142:
Channel Check Channel check allows
Page 143 and 144:
Chapter 9 Storing and Using Presets
Page 145 and 146:
Storing Presets using [Record Only]
Page 147 and 148:
Editing Presets Live There are two
Page 149 and 150:
Editing Presets in Blind All preset
Page 151 and 152:
Chapter 10 Storing and Using Palett
Page 153 and 154:
Storing Palettes Live Palettes may
Page 155 and 156:
Using Filters with Palettes Filters
Page 157 and 158:
Editing Palettes Live Note: Rerecor
Page 159 and 160:
Editing Palettes in Spreadsheet Vie
Page 161 and 162:
Deleting Palettes To delete color p
Page 163 and 164:
Chapter 11 Working with a Single Cu
Page 165 and 166:
Recording Cues in Live When using [
Page 167 and 168:
Using Selective Store You may use t
Page 169 and 170:
Timing Cue timing can be applied in
Page 171 and 172:
Delay Time Delay is used to stage t
Page 173 and 174:
Assigning Cue Attributes You can re
Page 175 and 176:
Rate The {Rate} softkey can be used
Page 177 and 178:
Assert Assert is a way to make a tr
Page 179 and 180:
Modifying Cues Live Recorded cues c
Page 181 and 182:
[Update] Update is a powerful featu
Page 183 and 184:
Using Cue Only/Track The [Cue Only/
Page 185 and 186:
Recording and Editing Cues from Bli
Page 187 and 188:
Replace With {Replace With} is used
Page 189 and 190:
Chapter 12 Using Mark {Mark} is an
Page 191 and 192:
Referenced Marks Referenced marks a
Page 193 and 194:
It is also possible to mark to a cu
Page 195 and 196:
Reference Marks and Timing Movement
Page 197 and 198:
Chapter 13 Using Filters Filters ar
Page 199 and 200:
To apply record filters by category
Page 201 and 202:
Chapter 14 Working with Multiple Cu
Page 203 and 204:
Using Assert By default, channel pa
Page 205 and 206:
Using [Go To Cue] with Multiple Cue
Page 207 and 208:
Cue List Attributes Cue list attrib
Page 209 and 210:
Chapter 15 Advanced Manual Control
Page 211 and 212:
Using [Recall From] [Recall From] i
Page 213 and 214:
Using {Make Manual} The {Make Manua
Page 215 and 216:
Using [Undo] Undo is a method to re
Page 217 and 218:
Chapter 16 Multipart Cues Cues can
Page 219 and 220:
Setting Multipart Cue Attributes Cu
Page 221 and 222:
Storing a Multipart Cue in Blind No
Page 223 and 224:
Chapter 17 Cue Playback Ion has man
Page 225 and 226:
Selected Cue The selected cue is al
Page 227 and 228:
Go To Cue [Go to Cue] instructions
Page 229 and 230:
Playback Fader Controls In Ion, man
Page 231 and 232:
Manual Intensity Override An intens
Page 233 and 234:
Using Stop Effect The {Stop Effect}
Page 235 and 236:
Chapter 18 Using Park This chapter
Page 237 and 238:
Parked Values in Live Channels and
Page 239 and 240:
Park Values from the Park Display Y
Page 241 and 242:
Chapter 19 Creating and Using Effec
Page 243 and 244:
Effects Editor When viewing the eff
Page 245 and 246:
Entry Establishes at what time and
Page 247 and 248:
Effect Status Display To view the e
Page 249 and 250:
Program a Step Effect Below is the
Page 251 and 252:
Absolute Effects Absolute effects a
Page 253 and 254:
Relative Effects A relative effect
Page 255 and 256:
Define a Pattern Shape Shapes can b
Page 257 and 258:
Effects on Submasters Channels runn
Page 259 and 260:
Chapter 20 Using About [About] prov
Page 261 and 262:
[About] When [About] is pressed, th
Page 263 and 264:
About Channel Press [About] to put
Page 265 and 266:
{Sensor AF} - appears when the curr
Page 267 and 268:
About Cue The following information
Page 269 and 270:
Chapter 21 Storing and Using Submas
Page 271 and 272:
Submaster Displays In the display w
Page 273 and 274:
Loading Submasters Submasters can b
Page 275 and 276:
Using Bump Button Timing With Subma
Page 277 and 278:
Chapter 22 Storing and Using Macros
Page 279 and 280:
Begin writing the sequence of butto
Page 281 and 282:
While in the macro editor display,
Page 283 and 284:
Edit an Existing Macro When you hav
Page 285 and 286:
Chapter 23 Storing and Using Curves
Page 287 and 288:
Creating and Editing Curves Creatin
Page 289 and 290:
Applying a Curve To Channels In Pat
Page 291 and 292:
Chapter 24 Using Show Control Ion s
Page 293 and 294:
Programming an Event List Getting s
Page 295 and 296:
Enabling the Clocks The internal an
Page 297 and 298:
Analog Inputs and Relay Outputs Ana
Page 299 and 300:
Set The “Set” command allows MS
Page 301 and 302:
Chapter 25 Multiple Users Ion can b
Page 303 and 304:
Chapter 26 Using Partitioned Contro
Page 305 and 306:
Creating New Partitions To create a
Page 307 and 308:
Appendix A Eos Configuration Utilit
Page 309 and 310:
Backup Backup mode requires a prima
Page 311 and 312:
Keyboard Allows you to select the l
Page 313 and 314:
Network Settings Ion Console IP Set
Page 315 and 316:
Ion IP Settings These are the setti
Page 317 and 318:
Backup Show Archive {Backup Show Ar
Page 319 and 320:
Ion This screen allows you to confi
Page 321 and 322:
Appendix B Multi-console and Synchr
Page 323 and 324:
Change IP Address All Ion consoles
Page 325 and 326:
Synchronized Backup Once you have c
Page 327 and 328:
Backup Scenarios Console and consol
Page 329 and 330:
Appendix C Remote Processor Unit (R
Page 331 and 332:
Software Configuration Settings for
Page 333 and 334:
Appendix D Remote Video Interface (
Page 335 and 336:
Front Panel Removable label strip B
Page 337 and 338:
Appendix E Remote Control Remotes O
Page 339 and 340:
Base Station Receiver The receiver
Page 341 and 342:
Basic Use Guidelines Keypad Functio
Page 343 and 344:
RFR Operation Modes The Eos/Ion RFR
Page 345 and 346:
Playback Mode Softkeys The followin
Page 347 and 348:
Technical Specifications Handheld T
Page 349 and 350:
Appendix F Universal Fader Wings Ov
Page 351 and 352:
then press down gently on the right
Page 353 and 354:
Using the Buttons Each fader is equ
Page 355 and 356:
Index Symbols -% . . . . . . . . .
Page 357 and 358:
in setup. . . . . . . . . . . . . .
Page 359 and 360:
programming . . . . . . . . . . . .
Page 361 and 362:
setting intensity with . . . . . .
Page 363 and 364:
faders . . . . . . . . . . . . . .
Page 365 and 366:
multipart cues. . . . . . . . . . .
Page 367 and 368:
T large . . . . . . . . . . . . . .
Page 370 and 371:
Corporate Headquarters 3031 Pleasa
Page 372 and 373:
identification, copyright notices,
Page 374 and 375:
measures in any relevant jurisdicti
Page 376 and 377:
) use the modified Package only wit
show all

ETC Ion - Theatre Uwinnipeg

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?