LTC Repair Lombardini Engine Troubleshooting - Wacker Neuson
LTC Repair Lombardini Engine Troubleshooting - Wacker Neuson LTC Repair Lombardini Engine Troubleshooting - Wacker Neuson
Maintenance LTC Repair 4.5 Replacing Bulbs See Graphic: wc_gr002464 Removal: 4.5.1 Shut down the engine and allow the bulb to cool. 4.5.2 Remove the screws (a) securing the flange rings (b) and remove the flange rings. 4.5.3 Remove the lens (c) with the gasket (d) attached. 4.5.4 Remove the hardware securing one side of the bulb stabilizer (e). Once removed, swing the bulb stabilizer to the side and unscrew the bulb (f). Installation: 4.5.5 Insert the bulb and secure it with the bulb stabilizer (e). 4.5.6 Install the gasket (d) around the lens (c) and secure the lens to the reflector with flange ring (b) and screws (a). c d a b 42 f e wc_gr002464
LTC Repair Maintenance 4.6 Air Cleaner See Graphic: wc_gr000540 Replace the air filter cartridge when the indicator (o) mounted on the control panel appears. 4.6.1 Open air cleaner and remove element. 4.6.2 To clean the filter, lightly tap on a hard surface to eliminate all excess dirt. Do not blow the paper filter element with compressed air to clean. Clean the filter cover and support carefully. 4.6.3 Reassemble the filtering element and air cleaner. 4.7 Engine Oil See Graphic: wc_gr000541 Drain the oil while the engine is still warm. Note: In the interests of environmental protection, place a plastic sheet and a container under the machine to collect any liquid which drains off. Dispose of this liquid in accordance with environmental protection legislation. 4.7.1 Remove the oil drain plug. 4.7.2 Allow the oil to drain. 4.7.3 Install the oil drain plug. 4.7.4 Fill the engine crankcase through the oil filler opening, to the upper mark on the dipstick. See Technical Data for oil quantity and type. 4.7.5 Install the oil filter cap. 43 wc_gr000540 wc_gr000541
- Page 1: www.wackergroup.com REPAIR MANUAL 0
- Page 4 and 5: Foreword LTC Repair WARNING 4 CALIF
- Page 6 and 7: Table of Contents LTC Repair 4.4 Pr
- Page 8 and 9: Table of Contents LTC Repair 7.12 R
- Page 10 and 11: Safety Information LTC Repair 1.2 O
- Page 12 and 13: Safety Information LTC Repair 1.4 T
- Page 14 and 15: Safety Information LTC Repair 1.6 L
- Page 16 and 17: Safety Information LTC Repair 1.7 S
- Page 18 and 19: Safety Information LTC Repair Ref.
- Page 20 and 21: Safety Information LTC Repair Ref.
- Page 22 and 23: Technical Data LTC 4L 2. Technical
- Page 24 and 25: Technical Data LTC 4L 2.2 Generator
- Page 26 and 27: Technical Data LTC 4L 26
- Page 28 and 29: Operation LTC 4L 3.3 Leveling Trail
- Page 30 and 31: Operation LTC 4L 3.6 Raising Tower
- Page 32 and 33: Operation LTC 4L 3.7 Lowering Tower
- Page 34 and 35: Operation LTC 4L 3.8 Control Panels
- Page 36 and 37: Operation LTC 4L 3.10 Starting See
- Page 38 and 39: Maintenance LTC Repair 4. Maintenan
- Page 40 and 41: Maintenance LTC Repair 4.3 Installi
- Page 44 and 45: Maintenance LTC Repair 44 4.8 Lomba
- Page 46 and 47: Maintenance LTC Repair 4.10 Engine
- Page 48 and 49: Maintenance LTC Repair 4.12 Wiring
- Page 50 and 51: Maintenance LTC Repair 4.14 Wiring
- Page 52 and 53: Maintenance LTC Repair 4.16 Wiring
- Page 54 and 55: Maintenance LTC Repair 4.18 Generat
- Page 56 and 57: Lombardini Engine Troubleshooting L
- Page 58 and 59: Lombardini Engine Troubleshooting L
- Page 60 and 61: Lombardini Engine Troubleshooting L
- Page 62 and 63: Lombardini Engine Troubleshooting L
- Page 64 and 65: Lombardini Engine Troubleshooting L
- Page 66 and 67: Lombardini Engine Troubleshooting L
- Page 68 and 69: Lombardini Engine Troubleshooting L
- Page 70 and 71: Lombardini Engine Troubleshooting L
- Page 72 and 73: Electrical Troubleshooting Procedur
- Page 74 and 75: Electrical Troubleshooting Procedur
- Page 76 and 77: Electrical Troubleshooting Procedur
- Page 78 and 79: Electrical Troubleshooting Procedur
- Page 80 and 81: Electrical Troubleshooting Procedur
- Page 82 and 83: Electrical Troubleshooting Procedur
- Page 84 and 85: Electrical Troubleshooting Procedur
- Page 86 and 87: Electrical Troubleshooting Procedur
- Page 88 and 89: Electrical Troubleshooting Procedur
- Page 90 and 91: Electrical Troubleshooting Procedur
Maintenance <strong>LTC</strong> <strong>Repair</strong><br />
4.5 Replacing Bulbs<br />
See Graphic: wc_gr002464<br />
Removal:<br />
4.5.1 Shut down the engine and allow the bulb to cool.<br />
4.5.2 Remove the screws (a) securing the flange rings (b) and remove the<br />
flange rings.<br />
4.5.3 Remove the lens (c) with the gasket (d) attached.<br />
4.5.4 Remove the hardware securing one side of the bulb stabilizer (e).<br />
Once removed, swing the bulb stabilizer to the side and unscrew the<br />
bulb (f).<br />
Installation:<br />
4.5.5 Insert the bulb and secure it with the bulb stabilizer (e).<br />
4.5.6 Install the gasket (d) around the lens (c) and secure the lens to the<br />
reflector with flange ring (b) and screws (a).<br />
c<br />
d<br />
a<br />
b<br />
42<br />
f<br />
e<br />
wc_gr002464