LTC Repair Lombardini Engine Troubleshooting - Wacker Neuson

More documents

Recommendations

Info

Disassembly/Assembly Procedures LTC Repair See Graphic: wc_gr003533 Reassembly: 7.10.9 Grease the adjusting point circle (a) of the main cradle and the bottom pivot point (b) of the main mast. 7.10.10 Using an appropriate crane or hoist, lift the main mast onto the top of the generator enclosure. Slide the bottom of the main mast into the main cradle. 7.10.11 Secure the main mast to the main cradle with the washer and nut (c). 7.10.12 Position the cable clip (d), on the tower supply cable, just below the lower curled portion of the cable. Then, secure the cable clip to the end of the main mast. 7.10.13 Thread the tower supply cable through the eyes (e) on the main mast. 7.10.14 Thread the tower supply cable through the clamp (f) at the front of the machine; leave a loop (g) of cable large enough so there is enough slack in the cable to raise the mast. 7.10.15 Feed the tower supply cable into the control box and connect the wires to the appropriate locations (h & i). Refer to the wiring diagram. Tighten the cable clamp (j), organize the wires with new wire ties (k), and re-install the control panel cover. 134
LTC Repair Disassembly/Assembly Procedures a f e g c b 135 j k d h i wc_gr003533
Page 1:
www.wackergroup.com REPAIR MANUAL 0
Page 4 and 5:
Foreword LTC Repair WARNING 4 CALIF
Page 6 and 7:
Table of Contents LTC Repair 4.4 Pr
Page 8 and 9:
Table of Contents LTC Repair 7.12 R
Page 10 and 11:
Safety Information LTC Repair 1.2 O
Page 12 and 13:
Safety Information LTC Repair 1.4 T
Page 14 and 15:
Safety Information LTC Repair 1.6 L
Page 16 and 17:
Safety Information LTC Repair 1.7 S
Page 18 and 19:
Safety Information LTC Repair Ref.
Page 20 and 21:
Safety Information LTC Repair Ref.
Page 22 and 23:
Technical Data LTC 4L 2. Technical
Page 24 and 25:
Technical Data LTC 4L 2.2 Generator
Page 26 and 27:
Technical Data LTC 4L 26
Page 28 and 29:
Operation LTC 4L 3.3 Leveling Trail
Page 30 and 31:
Operation LTC 4L 3.6 Raising Tower
Page 32 and 33:
Operation LTC 4L 3.7 Lowering Tower
Page 34 and 35:
Operation LTC 4L 3.8 Control Panels
Page 36 and 37:
Operation LTC 4L 3.10 Starting See
Page 38 and 39:
Maintenance LTC Repair 4. Maintenan
Page 40 and 41:
Maintenance LTC Repair 4.3 Installi
Page 42 and 43:
Maintenance LTC Repair 4.5 Replacin
Page 44 and 45:
Maintenance LTC Repair 44 4.8 Lomba
Page 46 and 47:
Maintenance LTC Repair 4.10 Engine
Page 48 and 49:
Maintenance LTC Repair 4.12 Wiring
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Maintenance LTC Repair 4.18 Generat
Page 56 and 57:
Lombardini Engine Troubleshooting L
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Electrical Troubleshooting Procedur
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85: Electrical Troubleshooting Procedur
Page 124 and 125: Disassembly/Assembly Procedures LTC
Page 142 and 143: Threadlockers and Sealants Threadlo
Page 144: Torque Values Torque Values (contin
show all

LTC Repair Lombardini Engine Troubleshooting - Wacker Neuson

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?