LTC Repair Lombardini Engine Troubleshooting - Wacker Neuson
LTC Repair Lombardini Engine Troubleshooting - Wacker Neuson LTC Repair Lombardini Engine Troubleshooting - Wacker Neuson
Disassembly/Assembly Procedures LTC Repair See Graphic: wc_gr003533 Reassembly: 7.10.9 Grease the adjusting point circle (a) of the main cradle and the bottom pivot point (b) of the main mast. 7.10.10 Using an appropriate crane or hoist, lift the main mast onto the top of the generator enclosure. Slide the bottom of the main mast into the main cradle. 7.10.11 Secure the main mast to the main cradle with the washer and nut (c). 7.10.12 Position the cable clip (d), on the tower supply cable, just below the lower curled portion of the cable. Then, secure the cable clip to the end of the main mast. 7.10.13 Thread the tower supply cable through the eyes (e) on the main mast. 7.10.14 Thread the tower supply cable through the clamp (f) at the front of the machine; leave a loop (g) of cable large enough so there is enough slack in the cable to raise the mast. 7.10.15 Feed the tower supply cable into the control box and connect the wires to the appropriate locations (h & i). Refer to the wiring diagram. Tighten the cable clamp (j), organize the wires with new wire ties (k), and re-install the control panel cover. 134
LTC Repair Disassembly/Assembly Procedures a f e g c b 135 j k d h i wc_gr003533
- Page 84 and 85: Electrical Troubleshooting Procedur
- Page 86 and 87: Electrical Troubleshooting Procedur
- Page 88 and 89: Electrical Troubleshooting Procedur
- Page 90 and 91: Electrical Troubleshooting Procedur
- Page 92 and 93: Electrical Troubleshooting Procedur
- Page 94 and 95: Electrical Troubleshooting Procedur
- Page 96 and 97: Electrical Troubleshooting Procedur
- Page 98 and 99: Electrical Troubleshooting Procedur
- Page 100 and 101: Electrical Troubleshooting Procedur
- Page 102 and 103: Electrical Troubleshooting Procedur
- Page 104 and 105: Electrical Troubleshooting Procedur
- Page 106 and 107: Electrical Troubleshooting Procedur
- Page 108 and 109: Electrical Troubleshooting Procedur
- Page 110 and 111: Electrical Troubleshooting Procedur
- Page 112 and 113: Electrical Troubleshooting Procedur
- Page 114 and 115: Electrical Troubleshooting Procedur
- Page 116 and 117: Electrical Troubleshooting Procedur
- Page 118 and 119: Electrical Troubleshooting Procedur
- Page 120 and 121: Electrical Troubleshooting Procedur
- Page 122 and 123: Electrical Troubleshooting Procedur
- Page 124 and 125: Disassembly/Assembly Procedures LTC
- Page 126 and 127: Disassembly/Assembly Procedures LTC
- Page 128 and 129: Disassembly/Assembly Procedures LTC
- Page 130 and 131: Disassembly/Assembly Procedures LTC
- Page 132 and 133: Disassembly/Assembly Procedures LTC
- Page 136 and 137: Disassembly/Assembly Procedures LTC
- Page 138 and 139: Disassembly/Assembly Procedures LTC
- Page 140 and 141: Disassembly/Assembly Procedures LTC
- Page 142 and 143: Threadlockers and Sealants Threadlo
- Page 144: Torque Values Torque Values (contin
Disassembly/Assembly Procedures <strong>LTC</strong> <strong>Repair</strong><br />
See Graphic: wc_gr003533<br />
Reassembly:<br />
7.10.9 Grease the adjusting point circle (a) of the main cradle and the bottom<br />
pivot point (b) of the main mast.<br />
7.10.10 Using an appropriate crane or hoist, lift the main mast onto the top of<br />
the generator enclosure. Slide the bottom of the main mast into the<br />
main cradle.<br />
7.10.11 Secure the main mast to the main cradle with the washer and nut (c).<br />
7.10.12 Position the cable clip (d), on the tower supply cable, just below the<br />
lower curled portion of the cable. Then, secure the cable clip to the end<br />
of the main mast.<br />
7.10.13 Thread the tower supply cable through the eyes (e) on the main mast.<br />
7.10.14 Thread the tower supply cable through the clamp (f) at the front of the<br />
machine; leave a loop (g) of cable large enough so there is enough<br />
slack in the cable to raise the mast.<br />
7.10.15 Feed the tower supply cable into the control box and connect the wires<br />
to the appropriate locations (h & i). Refer to the wiring diagram.<br />
Tighten the cable clamp (j), organize the wires with new wire ties (k),<br />
and re-install the control panel cover.<br />
134