LTC Repair Lombardini Engine Troubleshooting - Wacker Neuson
LTC Repair Lombardini Engine Troubleshooting - Wacker Neuson LTC Repair Lombardini Engine Troubleshooting - Wacker Neuson
Electrical Troubleshooting Procedures LTC Repair 6.26 Checking Wiring to/from Ballast Transformers See Graphic: wc_gr003528 WARNING Electric shock hazard. Only qualified personnel should conduct this test. To check the wiring to and from the ballast transformer(s): 6.26.1 Turn off the engine. 6.26.2 Remove the control panel front cover. 6.26.3 Remove the screws (a) that secure the control panel/cover of the ballast box (b). Position the control panel/cover of the ballast box so you can access the wiring to the ballast transformers. 6.26.4 Check the B/Y (black-yellow) wire(s) (c) that run from the circuit breaker(s) to the ballast transformer(s). Repair the wiring as needed. 6.26.5 Check the R (red) wire(s) (d) that run from the ballast transformer(s) to the ballast capacitor(s). Repair the wiring as needed. 6.26.6 Check the Y (yellow) wire(s) (e) labelled “COMMON” that run from the ballast transformer(s) to the neutral of the long terminal strip. Repair the wiring as needed. 6.26.7 If all wiring is OK and 400V±10% is not reaching the ballast capacitor, the ballast transformer has failed; replace it. 112
LTC Repair Electrical Troubleshooting c a b e 113 d e d c wc_gr003528
- Page 62 and 63: Lombardini Engine Troubleshooting L
- Page 64 and 65: Lombardini Engine Troubleshooting L
- Page 66 and 67: Lombardini Engine Troubleshooting L
- Page 68 and 69: Lombardini Engine Troubleshooting L
- Page 70 and 71: Lombardini Engine Troubleshooting L
- Page 72 and 73: Electrical Troubleshooting Procedur
- Page 74 and 75: Electrical Troubleshooting Procedur
- Page 76 and 77: Electrical Troubleshooting Procedur
- Page 78 and 79: Electrical Troubleshooting Procedur
- Page 80 and 81: Electrical Troubleshooting Procedur
- Page 82 and 83: Electrical Troubleshooting Procedur
- Page 84 and 85: Electrical Troubleshooting Procedur
- Page 86 and 87: Electrical Troubleshooting Procedur
- Page 88 and 89: Electrical Troubleshooting Procedur
- Page 90 and 91: Electrical Troubleshooting Procedur
- Page 92 and 93: Electrical Troubleshooting Procedur
- Page 94 and 95: Electrical Troubleshooting Procedur
- Page 96 and 97: Electrical Troubleshooting Procedur
- Page 98 and 99: Electrical Troubleshooting Procedur
- Page 100 and 101: Electrical Troubleshooting Procedur
- Page 102 and 103: Electrical Troubleshooting Procedur
- Page 104 and 105: Electrical Troubleshooting Procedur
- Page 106 and 107: Electrical Troubleshooting Procedur
- Page 108 and 109: Electrical Troubleshooting Procedur
- Page 110 and 111: Electrical Troubleshooting Procedur
- Page 114 and 115: Electrical Troubleshooting Procedur
- Page 116 and 117: Electrical Troubleshooting Procedur
- Page 118 and 119: Electrical Troubleshooting Procedur
- Page 120 and 121: Electrical Troubleshooting Procedur
- Page 122 and 123: Electrical Troubleshooting Procedur
- Page 124 and 125: Disassembly/Assembly Procedures LTC
- Page 126 and 127: Disassembly/Assembly Procedures LTC
- Page 128 and 129: Disassembly/Assembly Procedures LTC
- Page 130 and 131: Disassembly/Assembly Procedures LTC
- Page 132 and 133: Disassembly/Assembly Procedures LTC
- Page 134 and 135: Disassembly/Assembly Procedures LTC
- Page 136 and 137: Disassembly/Assembly Procedures LTC
- Page 138 and 139: Disassembly/Assembly Procedures LTC
- Page 140 and 141: Disassembly/Assembly Procedures LTC
- Page 142 and 143: Threadlockers and Sealants Threadlo
- Page 144: Torque Values Torque Values (contin
Electrical <strong>Troubleshooting</strong> Procedures <strong>LTC</strong> <strong>Repair</strong><br />
6.26 Checking Wiring to/from Ballast Transformers<br />
See Graphic: wc_gr003528<br />
WARNING<br />
Electric shock hazard. Only qualified personnel should conduct this<br />
test.<br />
To check the wiring to and from the ballast transformer(s):<br />
6.26.1 Turn off the engine.<br />
6.26.2 Remove the control panel front cover.<br />
6.26.3 Remove the screws (a) that secure the control panel/cover of the<br />
ballast box (b). Position the control panel/cover of the ballast box so<br />
you can access the wiring to the ballast transformers.<br />
6.26.4 Check the B/Y (black-yellow) wire(s) (c) that run from the circuit<br />
breaker(s) to the ballast transformer(s). <strong>Repair</strong> the wiring as needed.<br />
6.26.5 Check the R (red) wire(s) (d) that run from the ballast transformer(s) to<br />
the ballast capacitor(s). <strong>Repair</strong> the wiring as needed.<br />
6.26.6 Check the Y (yellow) wire(s) (e) labelled “COMMON” that run from the<br />
ballast transformer(s) to the neutral of the long terminal strip. <strong>Repair</strong><br />
the wiring as needed.<br />
6.26.7 If all wiring is OK and 400V±10% is not reaching the ballast capacitor,<br />
the ballast transformer has failed; replace it.<br />
112