Operation - Wacker Neuson

More documents

Recommendations

Info

Maintenance 5.5 Exciter 5.5.1 Check oil level: 1. Position vibration plate horizontally. 2. Open filler bore (30). 3. The oil level must reach the start of the thread of the filler bore. 4. If necessary, pour in Fuchs Titan Unic 10W40 MC through filler bore (use funnel 0,75 l). 5. Close filler bore. (Tightening torque 100 Nm) 5.5.2 Changing the oil: 1. Open filler bore (30). 2. Tilt vibration plate and keep it tilted until the oil has run out. 3. Place vibration plate in horizontal position. 4. Pour in 0,75 l Fuchs Titan Unic 10W40 MC through the filler bore. 5. Close filler bore. (Tightening torque 100 Nm) Do not pour in too much oil! Take notice: Please pay attention to the corresponding environmental laws when disposing of used engine oil. We recommend you carry the oil in a container to a central collecting point for used oils. Do not pour used engine oil into the garbage nor into the sewer system, waste pipes or even on the ground. T00997GB.fm 40 Oil
5.6 Exciter V-belt T00997GB.fm 41 Maintenance It is not necessary to retighten the V-belt owing to the use of the automatic centrifugal clutch. Should the V-belt width fall below 15,5 mm the V-belt must be replaced. 5.6.1 Changing the exciter V-belt: 1. Remove belt guard (31). 2. Undo screw (32). 3. Remove button (33), belleville spring (34), seal (35) and front segment of the V-belt pulley (10). 4. Change exciter V-belt (12). 5. Assemble the components in reverse order; make sure that the coloured marking on the pin (36) coincides with the marking on the V-belt pulley (10). Do not oil or grease clutch components (will damage the graphite bushes).
Page 1 and 2: Operator´s Manual 0226267en 002 03
Page 3 and 4: 1 Foreword 1 Foreword This operator
Page 5 and 6: 5 Table Of Contents 6.1 Forward spe
Page 7 and 8: DPU 2 Safety 2 Safety 2.1 Principle
Page 9 and 10: DPU 2 Safety Exclusion of liability
Page 11 and 12: DPU 2 Safety 2.3 Protective gear Wo
Page 13 and 14: DPU 2 Safety Work environment Famil
Page 15 and 16: DPU 2 Safety Avoiding crushing When
Page 17 and 18: DPU 2 Safety Safety precautions whe
Page 19 and 20: DPU 2 Safety Working on the battery
Page 21 and 22: DPU 2 Safety Pos. Label Description
Page 23 and 24: TD00692GB.fm 23 Technical Data Batt
Page 25 and 26: 2.3 Description of function T00994G
Page 27 and 28: Transport to work site /Recommendat
Page 29 and 30: 4. Operation 4.1 Starting 4.1.1 Con
Page 31 and 32: 4.3 Switching off T00996GB.fm 31 Op
Page 33 and 34: 4.6 Mechanical oil pressure control
Page 35 and 36: 4.8 Additional notes on starting at
Page 37 and 38: 5.2 Engine oil 5.2.1 Check oil leve
Page 39: 5.4 Hydraulic control 5.4.1 Check o
Page 43 and 44: 6.5 The charge control lamp will no
Page 45 and 46: 3 Disposal 3.1 Disposal of batterie
Page 47: Manufacturer Wacker Neuson SE Preu

Operation - Wacker Neuson

Create successful ePaper yourself

Delete template?

Save as template?