211i Operating Manual FabricatOr® - Victor Technologies - Europe

More documents

Recommendations

Info

FABRICATOR 211i SAFETY INSTRUCTIONS This Page Intentionally Blank SAFETY INSTRUCTIONS AND WARNINGS 1-8 Manual 0-5225
INTRODUCTION FABRICATOR 211i 2.01 How To Use This Manual To ensure safe operation, read the entire manual, including the chapter on safety instructions and warnings. Throughout this manual, the words WARNING, CAUTION, and NOTE may appear. Pay particular attention to the information provided under these headings. These special annotations are easily recognized as follows: ! WARNING A WARNING gives information regarding possible personal injury. CAUTION A CAUTION refers to possible equipment damage. NOTE A NOTE offers helpful information concerning certain operating procedures. You will also notice icons from the safety section appearing throughout the manual. These are to advise you of specific types of hazards or cautions related to the portion of information that follows. Some may have multiple hazards that apply and would look something like this: 2.02 Equipment Identification The unit’s identification number (specification or part number), model, and serial number usually appear on a nameplate attached to the control panel. In some cases, the nameplate may be attached to the rear panel. Equipment which does not have a control panel such as gun and cable assemblies is identified only by the specification or part number printed on the shipping container. Record these numbers on the bottom of page i for future reference. SECTION 2: INTRODUCTION 2.03 Receipt Of Equipment When you receive the equipment, check it against the invoice to make sure it is complete and inspect the equipment for possible damage due to shipping. If there is any damage, notify the carrier immediately to file a claim. Furnish complete information concerning damage claims or shipping errors to the location in your area listed in the inside back cover of this manual. Include all equipment identification numbers as described above along with a full description of the parts in error. Move the equipment to the installation site before un-crating the unit. Use care to avoid damaging the equipment when using bars, hammers, etc., to un-crate the unit. 2.04 Description The Thermal Arc Fabricator 211i is a self contained single phase multi process welding inverter that is capable of performing MIG (GMAW/FCAW), STICK (MMA) and LIFT TIG (GTAW) welding processes. The unit is equipped with an integrated wire feed unit, digital voltage and amperage meters, and a host of other features in order to fully satisfy the broad operating needs of the modern welding professional. The unit is also fully compliant to Standard EN 60974.1. The Thermal Arc Fabricator 211i provides excellent welding performance across a broad range of applications when used with the correct welding consumables and procedures. The following instructions detail how to correctly and safely set up the machine and give guidelines on gaining the best efficiency and quality from the Power Source. Please read these instructions thoroughly before using the unit. Manual 0-5225 2-1 INTRODUCTION
Page 1 and 2: 211i Operating Manual FabricatOr ®
Page 3 and 4: ! WARNINGS Read and understand this
Page 5: TABLE OF CONTENTS SECTION 6: KEY SP
Page 8 and 9: FABRICATOR 211i SAFETY INSTRUCTIONS
Page 16 and 17: FABRICATOR 211i INTRODUCTION 2.05 U
Page 18 and 19: FABRICATOR 211i INTRODUCTION 2.09 S
Page 20 and 21: FABRICATOR 211i INTRODUCTION This P
Page 22 and 23: FABRICATOR 211i INSTALLATION/SETUP
Page 42 and 43: FABRICATOR 211i BASIC WELDING Posit
Page 44 and 45: FABRICATOR 211i BASIC WELDING 1. St
Page 46 and 47: FABRICATOR 211i BASIC WELDING Therm
Page 48 and 49: FABRICATOR 211i BASIC WELDING Solvi
Page 50 and 51: FABRICATOR 211i BASIC WELDING 4.03
Page 52 and 53: FABRICATOR 211i BASIC WELDING Joint
Page 54 and 55: FABRICATOR 211i BASIC WELDING Makin
Page 56 and 57: FABRICATOR 211i BASIC WELDING 2. Ve
Page 58 and 59: FABRICATOR 211i BASIC WELDING B. Di
Page 64 and 65:
FABRICATOR 211i BASIC WELDING 4.06
Page 66 and 67:
FABRICATOR 211i BASIC WELDING This
Page 68 and 69:
FABRICATOR 211i PROBLEMS/SERVICE 8
Page 70 and 71:
FABRICATOR 211i PROBLEMS/SERVICE Po
Page 72 and 73:
FABRICATOR 211i PROBLEMS/SERVICE Th
Page 74 and 75:
FABRICATOR 211i REPLACEMENT PARTS T
Page 76 and 77:
THERMAL ARC - LIMITED WARRANTY TERM
Page 78:
Denton, TX USA U.S. Customer Care P
show all

211i Operating Manual FabricatOr® - Victor Technologies - Europe

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?