CutMaster True Service Manual - Victor Technologies - Europe

More documents

Recommendations

Info

CUTMASTER 35mm This Page Intentionally Blank INTRODUCTION 2T-4 <strong>Manual</strong> 0-5083
3.01 Unpacking SECTION 3 SYSTEM: INSTALLATION CUTMASTER 35mm 1. Use the packing lists to identify and account for each item. 2. Inspect each item for possible shipping damage. If damage is evident, contact your distributor and / or shipping company before proceeding with the installation. 3. Record Power Supply and Torch model and serial numbers, purchase date and vendor name, in the information block at the front of this manual. 3.02 Lifting Options The Power Supply includes a handle for hand lifting only. Be sure unit is lifted and transported safely and securely. ! WARNING Do not touch live electrical parts. Disconnect input power cord before moving unit. FALLING EQUIPMENT can cause serious personal injury and can damage equipment. HANDLE is not for mechanical lifting. • Only persons of adequate physical strength should lift the unit. • Lift unit by the handles, using two hands. Do not use straps for lifting. • Use optional cart or similar device of adequate capacity to move unit. • Place unit on a proper skid and secure in place before transporting with a fork lift or other vehicle. <strong>Manual</strong> 0-5083 3-1 INSTALLATION
Page 1 and 2: 35mm CUTMASTER PLASMA CUTTING SYST
Page 3 and 4: ! WARNINGS Read and understand this
Page 5 and 6: TABLE OF CONTENTS SECTION 1:GENERAL
Page 7 and 8: TABLE OF CONTENTS APPENDIX 1: SEQUE
Page 9 and 10: SECTION 1: GENERAL INFORMATION 1.01
Page 11 and 12: 14. American Welding Society Standa
Page 13 and 14: 1.06 Documents De Reference Consult
Page 15 and 16: 1.08 Statement of Warranty CUTMASTE
Page 17 and 18: SECTION 2 SYSTEM: INTRODUCTION 2.01
Page 19 and 20: 2.05 Input Wiring Specifications 3
Page 21 and 22: SECTION 2 TORCH: INTRODUCTION 2T.01
Page 23: B. Gas Distribution The single gas
Page 27 and 28: For CE units: EMC Input Power Filte
Page 29 and 30: Installing Optional Single - Stage
Page 31 and 32: SECTION 3 TORCH: INSTALLATION 3T.01
Page 33 and 34: SECTION 4 SYSTEM: OPERATION 4.01 Fr
Page 35 and 36: STANDOFF CutMaster 35mm Gas Pressur
Page 37 and 38: SECTION 4 TORCH: OPERATION 4T.01 To
Page 39 and 40: Torch Standoff Improper standoff (t
Page 41 and 42: Shield Cup With Straight Edge The d
Page 43 and 44: 4T.05 Gouging ! WARNINGS Be sure th
Page 45 and 46: 4T.07 Parts Selection for SL100Torc
Page 47 and 48: CUTMASTER 35mm Type Torch: SL100 Wi
Page 55 and 56: Catalog # Description Patent(s) 9-8
Page 57 and 58: 5.01 General Maintenance SECTION 5
Page 59 and 60: 5.04 Fault Indicator At initial pow
Page 61 and 62: This Page Intentionally Blank CUTMA
Page 63 and 64: Problem - Symptom Possible Cause Re
Page 65 and 66: If all of the Pre Power-Up Tests ar
Page 67 and 68: 11. Open the torch switch • DC LE
Page 69 and 70: 3. Open or improperly connected rib
Page 71 and 72: L. AC LED on, TEMP, GAS, DC LED's a
Page 73 and 74: 5.08 Pilot Arc Problems A. AC LED o
Page 75 and 76:
should drop to less than 1vdc when
Page 77 and 78:
C. Main arc transfers but current c
Page 79 and 80:
D. PCB 2 Capacitor / Relay Test 1.
Page 81 and 82:
J. PCB 2 Capacitor / Relay Test (wi
Page 83 and 84:
This Page Intentionally Blank CUTMA
Page 85 and 86:
CUTMASTER 35mm Signal Source/Destin
Page 87 and 88:
This Page Intentionally Blank CUTMA
Page 89 and 90:
A. CAPACITOR PCB 2 SIGNALS J1-1 +12
Page 91 and 92:
B. LOGIC PCB 3 LED INDICATORS NORMA
Page 93 and 94:
J2-1 +12VDC Supply for Fan MOT3 J2-
Page 95 and 96:
NOT USED TO MOT3 TO MOT2 (40A PCB J
Page 97 and 98:
SECTION 5 TORCH: SERVICE 5T.01 Gene
Page 99 and 100:
6.01 Introduction A. Parts List Bre
Page 101 and 102:
6.05 Front Panel Replacement Parts
Page 103 and 104:
6.07 Right Side Replacement Parts C
Page 105 and 106:
6.09 Replacement Parts for Hand Tor
Page 107 and 108:
1 2 3 12 4 10 10 11 5 9 CUTMASTER 3
Page 109 and 110:
SECTION 7: REPLACEMENT PROCEDURES 7
Page 111 and 112:
7.05 Front Panel Parts Replacement
Page 113 and 114:
B. Main Transformer (T1) Replacemen
Page 115 and 116:
5. Remove the fitting from the filt
Page 117 and 118:
6. Install the replacement Contacto
Page 119 and 120:
ACTION: Close external disconnect s
Page 121 and 122:
APPENDIX 3: TORCH PIN - OUT DIAGRAM
Page 123 and 124:
C. Automation Torch Connection Diag
Page 125 and 126:
3 3 SEC1 SEC1 D2 TS1 +12VDC NTC D59
Page 127 and 128:
GLOBAL CUSTOMER SERVICE CONTACT The
show all

CutMaster True Service Manual - Victor Technologies - Europe

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?