- Page 1 and 2: 35mm CUTMASTER PLASMA CUTTING SYST
- Page 3 and 4: ! WARNINGS Read and understand this
- Page 5 and 6: TABLE OF CONTENTS SECTION 1:GENERAL
- Page 7 and 8: TABLE OF CONTENTS APPENDIX 1: SEQUE
- Page 9 and 10: SECTION 1: GENERAL INFORMATION 1.01
- Page 11 and 12: 14. American Welding Society Standa
- Page 13 and 14: 1.06 Documents De Reference Consult
- Page 15: 1.08 Statement of Warranty CUTMASTE
- Page 19 and 20: 2.05 Input Wiring Specifications 3
- Page 21 and 22: SECTION 2 TORCH: INTRODUCTION 2T.01
- Page 23 and 24: B. Gas Distribution The single gas
- Page 25 and 26: 3.01 Unpacking SECTION 3 SYSTEM: IN
- Page 27 and 28: For CE units: EMC Input Power Filte
- Page 29 and 30: Installing Optional Single - Stage
- Page 31 and 32: SECTION 3 TORCH: INSTALLATION 3T.01
- Page 33 and 34: SECTION 4 SYSTEM: OPERATION 4.01 Fr
- Page 35 and 36: STANDOFF CutMaster 35mm Gas Pressur
- Page 37 and 38: SECTION 4 TORCH: OPERATION 4T.01 To
- Page 39 and 40: Torch Standoff Improper standoff (t
- Page 41 and 42: Shield Cup With Straight Edge The d
- Page 43 and 44: 4T.05 Gouging ! WARNINGS Be sure th
- Page 45 and 46: 4T.07 Parts Selection for SL100Torc
- Page 47 and 48: CUTMASTER 35mm Type Torch: SL100 Wi
- Page 49 and 50: CUTMASTER 35mm Type Torch: SL100 Wi
- Page 51 and 52: CUTMASTER 35mm Type Torch: SL100 Wi
- Page 53 and 54: CUTMASTER 35mm Type Torch: SL100 Wi
- Page 55 and 56: Catalog # Description Patent(s) 9-8
- Page 57 and 58: 5.01 General Maintenance SECTION 5
- Page 59 and 60: 5.04 Fault Indicator At initial pow
- Page 61 and 62: This Page Intentionally Blank CUTMA
- Page 63 and 64: Problem - Symptom Possible Cause Re
- Page 65 and 66: If all of the Pre Power-Up Tests ar
- Page 67 and 68:
11. Open the torch switch • DC LE
- Page 69 and 70:
3. Open or improperly connected rib
- Page 71 and 72:
L. AC LED on, TEMP, GAS, DC LED's a
- Page 73 and 74:
5.08 Pilot Arc Problems A. AC LED o
- Page 75 and 76:
should drop to less than 1vdc when
- Page 77 and 78:
C. Main arc transfers but current c
- Page 79 and 80:
D. PCB 2 Capacitor / Relay Test 1.
- Page 81 and 82:
J. PCB 2 Capacitor / Relay Test (wi
- Page 83 and 84:
This Page Intentionally Blank CUTMA
- Page 85 and 86:
CUTMASTER 35mm Signal Source/Destin
- Page 87 and 88:
This Page Intentionally Blank CUTMA
- Page 89 and 90:
A. CAPACITOR PCB 2 SIGNALS J1-1 +12
- Page 91 and 92:
B. LOGIC PCB 3 LED INDICATORS NORMA
- Page 93 and 94:
J2-1 +12VDC Supply for Fan MOT3 J2-
- Page 95 and 96:
NOT USED TO MOT3 TO MOT2 (40A PCB J
- Page 97 and 98:
SECTION 5 TORCH: SERVICE 5T.01 Gene
- Page 99 and 100:
6.01 Introduction A. Parts List Bre
- Page 101 and 102:
6.05 Front Panel Replacement Parts
- Page 103 and 104:
6.07 Right Side Replacement Parts C
- Page 105 and 106:
6.09 Replacement Parts for Hand Tor
- Page 107 and 108:
1 2 3 12 4 10 10 11 5 9 CUTMASTER 3
- Page 109 and 110:
SECTION 7: REPLACEMENT PROCEDURES 7
- Page 111 and 112:
7.05 Front Panel Parts Replacement
- Page 113 and 114:
B. Main Transformer (T1) Replacemen
- Page 115 and 116:
5. Remove the fitting from the filt
- Page 117 and 118:
6. Install the replacement Contacto
- Page 119 and 120:
ACTION: Close external disconnect s
- Page 121 and 122:
APPENDIX 3: TORCH PIN - OUT DIAGRAM
- Page 123 and 124:
C. Automation Torch Connection Diag
- Page 125 and 126:
3 3 SEC1 SEC1 D2 TS1 +12VDC NTC D59
- Page 127 and 128:
GLOBAL CUSTOMER SERVICE CONTACT The