DocLib_42_0-4905 ArcMaster 400MST CE.pdf - Victor Technologies ...
DocLib_42_0-4905 ArcMaster 400MST CE.pdf - Victor Technologies ...
DocLib_42_0-4905 ArcMaster 400MST CE.pdf - Victor Technologies ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Description Possible Cause Remedy Remarks<br />
6 E12 error code displayed<br />
Under mains supply<br />
(input) voltage primary<br />
capacitors is reduced for<br />
one second.<br />
7 E14 error code displayed<br />
Under mains supply<br />
(input) voltage warning<br />
primary capacitors is<br />
reduced for one second.<br />
8 E81 error code displayed<br />
Wrong Primary supply<br />
(input)<br />
voltage connected.<br />
9 E82 error code displayed<br />
Link switch plug not<br />
connected.<br />
10 E83 error code displayed<br />
CPU checks mains supply<br />
(input) voltage when the<br />
ON/OFF switch on rear<br />
panel of machine is turned<br />
ON.<br />
11 E85 error code<br />
displayed<br />
Pre-charge abnormality.<br />
12 E93 error code displayed<br />
Memory chip (EEPROM)<br />
on control PCB can not<br />
read/write weld<br />
parameters.<br />
Mains supply<br />
voltage is down to a<br />
dangerously low<br />
level.<br />
Mains supply<br />
voltage is less than<br />
the nominal<br />
operating voltage<br />
less 10%.<br />
When 3 phase<br />
machine is first<br />
turned ON with the<br />
wrong Primary<br />
supply (input)<br />
voltage connected.<br />
Link switch plug not<br />
connected.<br />
The Primary supply<br />
(input) voltage<br />
fluctuates and<br />
is not stable.<br />
Due to malfunction<br />
inside the Welding<br />
Power Source,<br />
primary capacitors<br />
are not charging<br />
correctly.<br />
Memory chip<br />
(EEPROM) error.<br />
53<br />
Have an accredited<br />
Thermal Arc Service<br />
Agent or a qualified<br />
electrician check the<br />
Mains voltage.<br />
Have an accredited<br />
Thermal Arc Service<br />
Agent or a qualified<br />
electrician check the<br />
Mains voltage.<br />
Have an accredited<br />
Thermal Arc Service<br />
Agent or a qualified<br />
electrician check<br />
the Mains voltage.<br />
Have an accredited<br />
Thermal Arc Service<br />
Agent check<br />
connector plug on<br />
input PCB.<br />
Have an accredited<br />
Thermal Arc Service<br />
Agent check<br />
connector plug on<br />
input PCB and the<br />
Mains voltage.<br />
Have an Accredited<br />
Thermal Arc<br />
Service Agent<br />
service the<br />
machine.<br />
Have an accredited<br />
Thermal Arc Service<br />
Agent check the<br />
control PCB.<br />
Weld current ceases.<br />
Buzzer sounds<br />
constantly.<br />
Error code E12<br />
automatically will reset<br />
when the voltage<br />
increases.<br />
Weld current available.<br />
Buzzer sounds<br />
intermittently. Error<br />
code E14 automatically<br />
will reset when the<br />
voltage increases.<br />
No weld current is<br />
available. Buzzer<br />
sounds constantly.<br />
Switch machine OFF.<br />
No weld current is<br />
available. Buzzer<br />
sounds constantly.<br />
Switch machine OFF.<br />
No weld current is<br />
available.<br />
Buzzer sounds<br />
constantly.<br />
Switch machine OFF<br />
then ON to reset E83<br />
error.<br />
No weld current is<br />
available. Buzzer<br />
sounds constantly.<br />
Switch machine OFF<br />
then ON to reset E85<br />
error.<br />
Weld current ceases.<br />
Buzzer sounds<br />
constantly.<br />
Switch machine OFF.