DocLib_42_0-4905 ArcMaster 400MST CE.pdf - Victor Technologies ...

More documents

Recommendations

Info

6. ON/OFF Switch This switch connects the Primary supply voltage to the inverter when in the ON position. This enables the Power Supply. 22 WARNING 5 When the welder is connected to the Primary supply voltage, the internal electrical components may be at 500V potential with respect to earth. 7. Input Cable The input cable connects the Primary supply voltage to the equipment. 8. 14/19 Pin Remote Control Select Switch User selectable switch. Position this switch for the remote control device socket to be utilized. The unselected Remote Control Socket is disabled at this time and cannot be utilized. Do not alter the position of this switch while one of the Remote Control Sockets is being utilized. 9. 24VAC Remote Device C/B Push to reset. Controls the 24VAC power source for the wire feeders controlled through the Remote Control Sockets. 10. 115VAC Remote Device C/B Push to reset. Controls the 115VAC power source for the wire feeders controlled through the Remote Control Sockets.
4.02 Weld Parameter Descriptions for ARC MASTER 400 MST Figure 5. ARC MASTER 400 MST Front Panel with Parameter Description Parameter Description This parameter provides a suitable short circuit current in STICK welding to improve electrode sticking and arc stability. ARC CONTROL HOT START DC (A) DC (V) Contactor ON/OFF This parameter operates in STICK weld mode and is used to improve the start characteristics for stick electrodes. e.g. low hydrogen electrodes. It sets the peak start current on top of the (WELD) current. Weld Current (Amperage) - when lit parameter knob sets the STICK and TIG WELD current. Weld Voltage (Volt) – when lit parameter knob sets the MIG voltage. Contactor operation in Stick Mode. 23
Page 1 and 2: 400 MST ARCMASTER ® Operating Manu
Page 3 and 4: WARNINGS Read and understand this e
Page 5: TABLE OF CONTENTS SECTION 7: BASIC
Page 8 and 9: ARCMASTER 400 MST 3. Use protective
Page 10 and 11: ARCMASTER 400 MST WARNING STEAM AND
Page 12 and 13: ARCMASTER 400 MST AVERTISSEMENT LE
Page 14 and 15: ARCMASTER 400 MST 1. Utilisez l’
Page 16 and 17: ARCMASTER 400 MST 10
Page 18 and 19: 2.01 How to Use This Manual This Ow
Page 20 and 21: 2.05 Functional Block Diagram Figur
Page 22 and 23: 3.04 Electrical Input Requirements
Page 24 and 25: 3.07 High Frequency Interference In
Page 26 and 27: 4.01 ARC MASTER 400 MST Controls 1
Page 30 and 31: Parameter Description Selects in op
Page 32 and 33: Vertical up welding When welding ve
Page 34 and 35: 7 4 3 SECTION 5: SEQUENCE OF OPERAT
Page 36 and 37: 5.03 MIG Welding • Connect work l
Page 38 and 39: 6.04 Guide for Selecting Filler Wir
Page 40 and 41: SECTION 7: BASIC STICK WELDING GUID
Page 42 and 43: 8.01 Setting of the Power Source SE
Page 44 and 45: SECTION 9: ROUTINE MAINTENANCE The
Page 46 and 47: Inconsistent Wire Feed WARNING Dise
Page 48 and 49: 8 Arc does not have a crisp sound,
Page 50 and 51: Description Possible Cause Remedy 8
Page 56 and 57: 11.03 Switching VRD On/Off Switch t
Page 58 and 59: SECTION 12: POWER SOURCE ERROR CODE
Page 60: Description Possible Cause Remedy R
Page 63 and 64: UB2 UB4 TB7 TB21 TB8 CT1 CT2 TB16 T
Page 66 and 67: LIMITED WARRANTY AND SCHEDULE This
Page 68: World Headquarters Thermadyne Holdi

DocLib_42_0-4905 ArcMaster 400MST CE.pdf - Victor Technologies ...

Create successful ePaper yourself

Delete template?

Save as template?