CutMaster True Service Manual - Victor Technologies - Europe

More documents

Recommendations

Info

CUTMASTER 25mm 6.04 Major External Replacement Parts Item # Qty Description Catalog # 1 1 Cover with labels 9-0222 2 1 Base Enclosure Assembly 9-0118 3 1 Tube, roll handle 9-0121 4 1 Front Panel 9-0228 5 1 Rear Panel 9-0101 3 Art # A-08120 Illustration may vary slightly from unit. 5 2 NOTE PARTS LIST 6-2 <strong>Manual</strong> 0-5081 1 4 3
6.05 Front Panel Replacement Parts CUTMASTER 25mm Item# Qty Description Ref. Catalog # 1 1 Output Current Control and Function Control Knobs 9-8527 2 1 Toggle - On/Off Switch SW1 9-0109 3 1 Work Cable with Clamp, 20 Ft / 6.1 m 9-0184 Not Shown: 1 Wire harness (from SW1) w/EMI Choke (CE Power Supplies Only) 9-0247 Illustration may vary slightly from unit. 1 3 2 NOTE Art # A-08123 <strong>Manual</strong> 0-5081 6-3 PARTS LIST
Page 1 and 2:
25mm CUTMASTER PLASMA CUTTING SYST
Page 3 and 4:
! WARNINGS Read and understand this
Page 5 and 6:
TABLE OF CONTENTS SECTION 1:GENERAL
Page 7 and 8:
TABLE OF CONTENTS APPENDIX 1: SEQUE
Page 9 and 10:
SECTION 1: GENERAL INFORMATION 1.01
Page 11 and 12:
14. American Welding Society Standa
Page 13 and 14:
1.06 Documents De Reference Consult
Page 15 and 16:
1.08 Statement of Warranty CUTMASTE
Page 17 and 18:
SECTION 2 SYSTEM: INTRODUCTION 2.01
Page 19 and 20:
2.05 Input Wiring Specifications 3
Page 21 and 22:
SECTION 2 TORCH: INTRODUCTION 2T.01
Page 23 and 24:
B. Gas Distribution The single gas
Page 25 and 26:
3.01 Unpacking SECTION 3 SYSTEM: IN
Page 27 and 28:
For CE units: EMC Input Power Filte
Page 29 and 30:
Installing Optional Single - Stage
Page 31 and 32:
SECTION 3 TORCH: INSTALLATION 3T.01
Page 33 and 34:
SECTION 4 SYSTEM: OPERATION 4.01 Fr
Page 35 and 36:
STANDOFF CutMaster 25mm Gas Pressur
Page 37 and 38:
SECTION 4 TORCH: OPERATION 4T.01 To
Page 39 and 40: Torch Standoff Improper standoff (t
Page 41 and 42: Shield Cup With Straight Edge The d
Page 43 and 44: 4T.05 Gouging ! WARNINGS Be sure th
Page 45 and 46: 4T.07 Parts Selection for Manual an
Page 47 and 48: CUTMASTER 25mm Type Torch: SL60 Wit
Page 49 and 50: CUTMASTER 25mm Type Torch: SL60 wit
Page 55 and 56: Catalog # Description Patent(s) 9-8
Page 57 and 58: 5.01 General Maintenance SECTION 5
Page 59 and 60: 5.04 Fault Indicator At initial pow
Page 61 and 62: Problem - Symptom Possible Cause Re
Page 63 and 64: 5. Remove the fitting from the filt
Page 65 and 66: B. Cover Installation 1. Reverse pr
Page 67 and 68: 9. Close torch switch (Pendant swit
Page 69 and 70: 3. Open or improperly connected rib
Page 71 and 72: L. AC LED on, TEMP, GAS, DC LED's a
Page 73 and 74: 4. Shorted Torch a) Disconnect torc
Page 75 and 76: 5.12 Test Procedures A. Main Contac
Page 77 and 78: Signal Information Many of the sign
Page 79 and 80: B. CAPACITOR PCB TEST POINTS MTH1,2
Page 81 and 82: CUTMASTER 25mm Signal Source/Destin
Page 83 and 84: This Page Intentionally Blank CUTMA
Page 85 and 86: J3-1 N/A J3-2 Common J4-1 3.3VDc J4
Page 87 and 88: SECTION 5 TORCH: SERVICE 5T.01 Gene
Page 89: 6.01 Introduction A. Parts List Bre
Page 93 and 94: 6.07 Right Side Replacement Parts C
Page 95 and 96: 6.09 Replacement Parts for Hand Tor
Page 97 and 98: 1 2 3 12 4 10 10 11 5 9 CUTMASTER 2
Page 99 and 100: SECTION 7: REPLACEMENT PROCEDURES 7
Page 101 and 102: 7.05 Front Panel Parts Replacement
Page 103 and 104: 13. Remove the two screws securing
Page 105 and 106: 7.08 Right Side Internal Parts Repl
Page 107 and 108: ACTION: Close external disconnect s
Page 109 and 110: APPENDIX 3: TORCH PIN - OUT DIAGRAM
Page 111 and 112: C. Automation Torch Connection Diag
Page 113 and 114: CUTMASTER 25MM Manual 0-5081 A-7 AP
Page 115 and 116: GLOBAL CUSTOMER SERVICE CONTACT The
show all

CutMaster True Service Manual - Victor Technologies - Europe

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?