CutMaster True Service Manual - Victor Technologies - Europe

More documents

Recommendations

Info

CUTMASTER 25mm 5.13 Capacitor PCB Layout & Signals MTH8 MTH7 MTH5 MTH6 MTH1 MTH3 MTH4 MTH2 A. CAPACITOR PCB SIGNALS J1-1 Capacitor bank A+ J1-5 Capacitor bank A- J2-1 Capacitor Bank B+ J2-5 Capacitor Bank B- *J3 CONNECTOR PINOUT 1 2 3 CAPACITOR PCB LAYOUT SERVICE 5-22 <strong>Manual</strong> 0-5081 J3* Art # A-08841 Signal Source/Destination J3-1 +12 VDC M-C J3-2 /400 Active low for 400VAC input M-C J3-2 N/A
B. CAPACITOR PCB TEST POINTS MTH1,2 Capacitor bank A+ MTH3,4 Capacitor bank A- MTH6,8 Capacitor Bank B+ MTH 5,7 Capacitor Bank B- CUTMASTER 25mm <strong>Manual</strong> 0-5081 5-23 SERVICE
Page 1 and 2:
25mm CUTMASTER PLASMA CUTTING SYST
Page 3 and 4:
! WARNINGS Read and understand this
Page 5 and 6:
TABLE OF CONTENTS SECTION 1:GENERAL
Page 7 and 8:
TABLE OF CONTENTS APPENDIX 1: SEQUE
Page 9 and 10:
SECTION 1: GENERAL INFORMATION 1.01
Page 11 and 12:
14. American Welding Society Standa
Page 13 and 14:
1.06 Documents De Reference Consult
Page 15 and 16:
1.08 Statement of Warranty CUTMASTE
Page 17 and 18:
SECTION 2 SYSTEM: INTRODUCTION 2.01
Page 19 and 20:
2.05 Input Wiring Specifications 3
Page 21 and 22:
SECTION 2 TORCH: INTRODUCTION 2T.01
Page 23 and 24:
B. Gas Distribution The single gas
Page 25 and 26:
3.01 Unpacking SECTION 3 SYSTEM: IN
Page 27 and 28: For CE units: EMC Input Power Filte
Page 29 and 30: Installing Optional Single - Stage
Page 31 and 32: SECTION 3 TORCH: INSTALLATION 3T.01
Page 33 and 34: SECTION 4 SYSTEM: OPERATION 4.01 Fr
Page 35 and 36: STANDOFF CutMaster 25mm Gas Pressur
Page 37 and 38: SECTION 4 TORCH: OPERATION 4T.01 To
Page 39 and 40: Torch Standoff Improper standoff (t
Page 41 and 42: Shield Cup With Straight Edge The d
Page 43 and 44: 4T.05 Gouging ! WARNINGS Be sure th
Page 45 and 46: 4T.07 Parts Selection for Manual an
Page 47 and 48: CUTMASTER 25mm Type Torch: SL60 Wit
Page 49 and 50: CUTMASTER 25mm Type Torch: SL60 wit
Page 55 and 56: Catalog # Description Patent(s) 9-8
Page 57 and 58: 5.01 General Maintenance SECTION 5
Page 59 and 60: 5.04 Fault Indicator At initial pow
Page 61 and 62: Problem - Symptom Possible Cause Re
Page 63 and 64: 5. Remove the fitting from the filt
Page 65 and 66: B. Cover Installation 1. Reverse pr
Page 67 and 68: 9. Close torch switch (Pendant swit
Page 69 and 70: 3. Open or improperly connected rib
Page 71 and 72: L. AC LED on, TEMP, GAS, DC LED's a
Page 73 and 74: 4. Shorted Torch a) Disconnect torc
Page 75 and 76: 5.12 Test Procedures A. Main Contac
Page 77: Signal Information Many of the sign
Page 81 and 82: CUTMASTER 25mm Signal Source/Destin
Page 83 and 84: This Page Intentionally Blank CUTMA
Page 85 and 86: J3-1 N/A J3-2 Common J4-1 3.3VDc J4
Page 87 and 88: SECTION 5 TORCH: SERVICE 5T.01 Gene
Page 89 and 90: 6.01 Introduction A. Parts List Bre
Page 91 and 92: 6.05 Front Panel Replacement Parts
Page 93 and 94: 6.07 Right Side Replacement Parts C
Page 95 and 96: 6.09 Replacement Parts for Hand Tor
Page 97 and 98: 1 2 3 12 4 10 10 11 5 9 CUTMASTER 2
Page 99 and 100: SECTION 7: REPLACEMENT PROCEDURES 7
Page 101 and 102: 7.05 Front Panel Parts Replacement
Page 103 and 104: 13. Remove the two screws securing
Page 105 and 106: 7.08 Right Side Internal Parts Repl
Page 107 and 108: ACTION: Close external disconnect s
Page 109 and 110: APPENDIX 3: TORCH PIN - OUT DIAGRAM
Page 111 and 112: C. Automation Torch Connection Diag
Page 113 and 114: CUTMASTER 25MM Manual 0-5081 A-7 AP
Page 115 and 116: GLOBAL CUSTOMER SERVICE CONTACT The
show all

CutMaster True Service Manual - Victor Technologies - Europe

Create successful ePaper yourself

Delete template?

Save as template?