- Page 1 and 2: 25mm CUTMASTER PLASMA CUTTING SYST
- Page 3: ! WARNINGS Read and understand this
- Page 7 and 8: TABLE OF CONTENTS APPENDIX 1: SEQUE
- Page 9 and 10: SECTION 1: GENERAL INFORMATION 1.01
- Page 11 and 12: 14. American Welding Society Standa
- Page 13 and 14: 1.06 Documents De Reference Consult
- Page 15 and 16: 1.08 Statement of Warranty CUTMASTE
- Page 17 and 18: SECTION 2 SYSTEM: INTRODUCTION 2.01
- Page 19 and 20: 2.05 Input Wiring Specifications 3
- Page 21 and 22: SECTION 2 TORCH: INTRODUCTION 2T.01
- Page 23 and 24: B. Gas Distribution The single gas
- Page 25 and 26: 3.01 Unpacking SECTION 3 SYSTEM: IN
- Page 27 and 28: For CE units: EMC Input Power Filte
- Page 29 and 30: Installing Optional Single - Stage
- Page 31 and 32: SECTION 3 TORCH: INSTALLATION 3T.01
- Page 33 and 34: SECTION 4 SYSTEM: OPERATION 4.01 Fr
- Page 35 and 36: STANDOFF CutMaster 25mm Gas Pressur
- Page 37 and 38: SECTION 4 TORCH: OPERATION 4T.01 To
- Page 39 and 40: Torch Standoff Improper standoff (t
- Page 41 and 42: Shield Cup With Straight Edge The d
- Page 43 and 44: 4T.05 Gouging ! WARNINGS Be sure th
- Page 45 and 46: 4T.07 Parts Selection for Manual an
- Page 47 and 48: CUTMASTER 25mm Type Torch: SL60 Wit
- Page 49 and 50: CUTMASTER 25mm Type Torch: SL60 wit
- Page 51 and 52: CUTMASTER 25mm Type Torch: SL60 Wit
- Page 53 and 54: CUTMASTER 25mm Type Torch: SL60 Wit
- Page 55 and 56:
Catalog # Description Patent(s) 9-8
- Page 57 and 58:
5.01 General Maintenance SECTION 5
- Page 59 and 60:
5.04 Fault Indicator At initial pow
- Page 61 and 62:
Problem - Symptom Possible Cause Re
- Page 63 and 64:
5. Remove the fitting from the filt
- Page 65 and 66:
B. Cover Installation 1. Reverse pr
- Page 67 and 68:
9. Close torch switch (Pendant swit
- Page 69 and 70:
3. Open or improperly connected rib
- Page 71 and 72:
L. AC LED on, TEMP, GAS, DC LED's a
- Page 73 and 74:
4. Shorted Torch a) Disconnect torc
- Page 75 and 76:
5.12 Test Procedures A. Main Contac
- Page 77 and 78:
Signal Information Many of the sign
- Page 79 and 80:
B. CAPACITOR PCB TEST POINTS MTH1,2
- Page 81 and 82:
CUTMASTER 25mm Signal Source/Destin
- Page 83 and 84:
This Page Intentionally Blank CUTMA
- Page 85 and 86:
J3-1 N/A J3-2 Common J4-1 3.3VDc J4
- Page 87 and 88:
SECTION 5 TORCH: SERVICE 5T.01 Gene
- Page 89 and 90:
6.01 Introduction A. Parts List Bre
- Page 91 and 92:
6.05 Front Panel Replacement Parts
- Page 93 and 94:
6.07 Right Side Replacement Parts C
- Page 95 and 96:
6.09 Replacement Parts for Hand Tor
- Page 97 and 98:
1 2 3 12 4 10 10 11 5 9 CUTMASTER 2
- Page 99 and 100:
SECTION 7: REPLACEMENT PROCEDURES 7
- Page 101 and 102:
7.05 Front Panel Parts Replacement
- Page 103 and 104:
13. Remove the two screws securing
- Page 105 and 106:
7.08 Right Side Internal Parts Repl
- Page 107 and 108:
ACTION: Close external disconnect s
- Page 109 and 110:
APPENDIX 3: TORCH PIN - OUT DIAGRAM
- Page 111 and 112:
C. Automation Torch Connection Diag
- Page 113 and 114:
CUTMASTER 25MM Manual 0-5081 A-7 AP
- Page 115 and 116:
GLOBAL CUSTOMER SERVICE CONTACT The